Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenmore Dateigröße: 1.72 mb Dateiname: Unterrichtssprache:

Wail Sleeve Dimensions (inches) Brand Width Height Depth White-Westinghouse 25-1/2 15-1/4 16, 17-1/2 Frigidaire or 22 Carrier (52F series) General Electric 26 15-5/8 16-7/8 /Hotpoint 17-1/8 Whirlpool 25-7/8 16-1/2 or 23 Fedders/Emerson 27 16-3/4 16-3/4 or 19-3/4 Sears/Kenmore 25-7/8 15-17/32 16-23/32 Emerson/Fedders 26-3/4 15-3/4 15 Carrier (51S Series) 25-3/4 16-7/8 18-5/8 Friedrich 27 16-3/4 16-3/4 NOTE: All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. I_ Remove old air conditioner from existing wall sleeve. i[_l Clean the interior of an existing sleeve. (Do not disturb seals.) I_ll Wall sleeve must be securely fastened in wall before installing the air conditioner. Use the nails or screws through sleeve into wall, if needed. Repaint sleeve if needed. II_ Prepare the wall sleeve for installation of the unit. If you plan to use your existing wall sleeve, and it is not Kenmore, use procedure B or C below. Procedure Brand Depth(inches) A Sears/Kenmore 16-23/32 White-Westinghouse Frigidaire Carrier (52F series) 16, 17-1/2 or 22 General Electric /Hotpoint 16-7/8 Whirlpool 17-1/8 or 23 Carrier (51S series) 18-5/8 C Fedders/Emerson Emerson/Fedders 16-3/4 or 19-3/4 15 Friedrich 16-3/4 rlt install new unit into wall sleeve. CAUTION: When installation is completed, replacement unit MUST have a rearward slope as shown. To achieve 1/4" slope, remove the backing from the 11-13/16" shim strips and attach them as shown below in Fig. 3. Place the higher portion of shim to the front of the rib on base of wall sleeve. I3/4 .i0. UNIT Wall sleeve SHIM PLACEMENT UNIT INSTALLATION FiG. 3 -6 PROCEDURE A If you are using the new sleeve (optionally supplied with your unit),skip to step 3. Otherwise, install the plastic grille from the kit. Cat the plastic grille to 25-1/2" wide and 15-1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange. FIG. 4 I_ll Fasten the 4 washer screws to secure the grille to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressing into the square holes of the rear flanges. J or FIG. 5 Ell Remove the backing from the Vertical Insulation strip 159/16x 13/8x 13/8and attach that to the inside right of the sleeve as shown below. Remove the backing from the Around Insulation strip 67% x 13/8x 25/32and attach that to the inside front of the sleeve as shown below. Indoor Outdoor / " 9V2" =i_ 6" _i FIG. 6 I_ll Remove the metal rear grille and replace it with the plastic rear grille to improve unit energy efficiency. The plastic grille reduces the amount of hot air discharge that recirculates through the unit. Plastic rear grilte Steelrear FIG. 7 II_ Install the new unit into the wall sleeve. rltTo assemble trim, snap the tab of each piece into the slot of the other piece as shown below. Slide trim over the front of the air conditioner until trim is flush with sleeve as shown below. / Trim (2 ea) Wall FIG. 8 • Airconditionerscoveredinthismanualposean excessiveweighthazard.Twoormorepeopleare neededto moveandinstallthe unit. Topreventinjuryor strain,useproperliftingand carryingtechniqueswhenmovingunit. •Whenhandlingtheair conditioner,becarefulto avoid cutsfromsharpmetalfins onfrontandrearcoils. • Makesureairconditionerdoesnotfall during removal. • If unitdoes notoperateafterinstallationcheck,to be surethe circuitinterrupterhasnot beentripped.Refer tothe Troubleshootingguidefor resetprocedure. -7 PROCEDURE B _1 Redirect the louvers at the back of the wall sleeve to 60 ° angle as shown in the FiG 9. The use of pliers is recommended. 7 3/32 '= Rear Lo LlVel'$ (Top View) FIG. 9 _llf the wall sleeve already has a rear grille, skip to step 4. If the wall sleeve does not have a rear grille or Iouvered panel, install the plastic grille from the kit. Cut the plastic grille to 25-1/2" wide and 15-1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange Place the plastic grille FIG. 1[} _1 Fasten the 4 washer screws to secure the grille to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges. _J Remove the backing from the Vertical Insulation strip 15%6 x 13/8x 13/8 and attach that to the inside right of the sleeve as shown below. Remove the backing from the Around Insulation strip 671/8x 1_/3x 25/32and attach that to the inside front of the sleeve as shown below. Indoor Outdoor 9V2" i 6"I FIG. 12 O Remove the metal rear grille and replace it with the plastic rear grille to improve unit energy efficiency. The plastic grille reduces the amount ...

Herunterladen

Geben Sie zwei Ziffern: