Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Freecom Technologies Dateigröße: 154.65 kb Dateiname: Unterrichtssprache:

The default temperature is 77.F. Press right button to lower cooling setting; press left button to raise cooling setting. Each press of the button will adjust the temperature approximately 1.F. The temperature setting can be adjusted from 68.F to 86.F. CAUTION: To avoid injury or damage and voiding the warranty, DO NOT manually adjust the louvers. 5. Press “AUTO SWING” button on control panel to begin oscillating horizontal louvers. The louvers will move slowly up and down for optimum air distribution. Press button again to maintain a desired “fixed” position to distribute more cooling air to one side of the room. OPERATION (contd.) Operating the Timer If you wish to check the timer setting after the timer has been programmed, press the "TIMER-SET" button on control panel while timer "ON" or "OFF" light is on. The display will show the hours remaining until the timer function is operating. Pressing "TIMERSET" again will increase timer setting. ToTurnUnitOnwithTimer 1. While the unit is off, press “TIMER-SET” button on control panel to program the air conditioning unit to turn on in 1-24 hours. The timer "ON" light will turn on. You may also set Mode and Thermo Control settings at this time. The unit will turn on at the programmed time. If you wish to check the timer, press the "TIMER-SET" button on control panel while timer "ON" light is on. The display will show the hours remaining until the timer function is operating. Pressing "TIMER-SET" again will increase timer setting. 2. To cancel timer setting, press "TIMER-RESET" button. If the power on/off "I/O" button is pressed while a timer "ON"setting is scheduled, the timer function will be cancelled and the unit will continue to operate as normal. ToTurnUnitOffwithTimer 1. While the unit is on, press “TIMER-SET” button on control panel to program the air conditioning unit to turn off in 1-24 hours. The timer "OFF" light will turn on. The unit will turn off at the programmed time. 2. To cancel timer setting, press "TIMER-RESET" button. If the power on/off "I/O" button is pressed while a timer "OFF" setting is scheduled, the unit will turn off and the programmed "OFF" time will be cleared. Wireless Remote Control Operation The Wireless Remote Control has the same control buttons as are on the Control Panel. All functions operate the same as described under "CONTROL PANEL." The remote requires two "AAA" size batteries (included). NOTE: The Wireless Remote Control will operate up to 16 feet (5 meters) from indoor unit. 1. Press "POWER on/off" button to remotely operate unit. 2. Press function buttons, as desired, to control air conditioner. See "CONTROL PANEL" for button controls and functions. MAINTENANCE AND CLEANING Draining Water Tank When the condensate water tank is full, the “DRAIN WATER” indicator light will flash, the unit will sound several initial warning beeps, and the unit will automatically turn off. IMPORTANT: For the indoor unit's condensate drain pump to function properly, the outdoor unit must not be more than 6 feet above indoor unit. NOTE: If emptying water tank before “DRAIN WATER” alert, press Power On/Off "I/O" button to stop unit if it is operating. 1. Unplug power cord from outlet. Allow unit to remain off for 3-5 minutes. 2. Remove screw from from plastic mounting bracket on drain tube. 3. Remove plug from condensate tube (on back of indoor unit) and drain water into a shallow bucket. Be sure tank is completely empty. Replace plug tightly onto end of tube. 4. Replace tube and plastic mounting bracket to original position. 5. Plug power cord into outlet. Press Power On/Off ("I/O") button. MAINTENANCE AND CLEANING (contd.) Cleaning Air Filter This unit has one air filter. For best results and maximum performance, clean filter every two weeks, or as required by environmental conditions. CAUTION: Neglect or failure to regularly clean the filter will result in poor efficiency, reduced performance, possible damage to the unit, and voiding your warranty. 1. Press Power On/Off "I/O" button to stop unit if it is operating. Unplug power cord from outlet. 2. Locate filter on top, rear side of indoor unit. Carefully pull filter from top of indoor unit. 3. Place air filter on a flat, level surface so “dirty” side of filter faces up. Using a brush or nozzle vacuum attachment, gently vacuum “dirty” side of filter. Turn filter over and vacuum other side. Use care not to damage or puncture the filter mesh. DO NOT use brushes, brooms, or other course materials to clean the filters. 4. Hold air filter, “dirty” side down, under cool, running water. DO NOT use hot water, harsh detergents, chemicals, solvents, gasoline or any other abrasive materials or household items to clean the filters. Be sure to rinse all residue from the air filter mesh. Carefully shake air filter to remove excess water. Allow air filter to dry completely before reinstalling into unit. WARNING: Forcing filter improperly into unit may cause damage. Repair due to improper filter instal...

Herunterladen

Geben Sie zwei Ziffern: