Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: LG Dateigröße: 12.04 mb Dateiname: fd543c9c-a3f9-4e39-bf98-098e798d9b8a.pdf Unterrichtssprache:

Do not change plug in any way. Do not use an adapter plug. If your present wall outlet does not match your plug, call a qualified electrician to make the necessary corrections. SAVE CARTON for storage and this OWNER'S MANUAL for future reference. The carton is the best way to store unit during winter or when not in use. INSTALLATION HARDWARE To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: • Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. • Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. • Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. • Make sure air conditioner does not fall during installation. CAUTION REQUIRED TOOLS: • Tight Fitting gloves • Standard screwdriver • Phillips screwdriver • Pliers • Sharp knife • 3/8-inch open end wrench or adjustable wrench • 1/4-inch hex socket and ratchet • Tape measure • Electric drill • 1/4-inch drill bit 14-13/32" (366 mm) 24"(610 mm) 18-15/32"(468 mm) 20-3/32" (511 mm) Air Conditioner FIG. 18A 15-17/32" (394 mm) 16-23/32" (425 mm) 25-7/8" (656 mm) aluminum metal grille FRIEDRICH USC Wall Sleeve FIG. 18B ITEM NAME OF PARTS Q'TY PLASTIC GRILLE 1 VERTICAL INSULATION STRIP 1 AROUND INSULATION STRIPS 2 HORIZONTAL INSULATION STRIP 1 SUPPORT BLOCK 2 BAFFLE 1 TRIM FRAME 2 SHIM 2 PLASTIC NUTS AND WASHER SCREWS 4 1 5 6 7 8 3 2 4 9 2 Size options 2 Size options 3.2 INSTALLATION CAUTION Installing the FRIEDRICH USC sleeve ensures optional performances of the unit. If you decide to keep the existing wall sleeve, you have to redirect the louvers at the back of the wall sleeve. Refer to FIG. 23 on p15. The use of pliers is recommended. If you DO NOT redirect, you run the risk of poor performance or premature product failure. This is not covered under the terms of the FRIEDRICH warranty. • Pick a location which will allow the conditioned air to blow into the area you want. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed. ITEMS IN INSTALLATION HARDWARE You may not need all parts in the kit. Discard unused parts ITEM (inches) Qty. Plastic grille 263/4 x 161/2 1 Vertical insulation strip 159/16 x 13/8 x 13/8 1 Around Insulation Strips 671/8 x 13/8 x 25/32 1 5927/32 x 13/8 x 13/8 1 Horizontal Insulation Strip 237/32 x 13/8 x 13/16 1 Support Block 13/4 x 13/8 x 45/16 2 Baffle 14 x 41/2 x 1/8 1 Shim 1113/16 x 1 x 3/4 2 Trim Frame 2 Washer Screw 4 Nuts(Plastic) 4 Grille Rear 1 HOW TO INSTALL 1 Before installing the unit, identify the existing wall sleeve from the list below. NOTE: All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. 2 3 4 5 Remove old air conditioner from existing wall sleeve. Clean the interior of an existing sleeve. (Do not disturb seals.) Wall sleeve must be securely fastened in wall before installing the air conditioner. Use the nails or screws through sleeve into wall, if needed. Repaint sleeve if needed. Prepare the wall sleeve for installation of the unit. If you plan to use your existing wall sleeve, and it is not FRIEDRICH, use procedure B or C below. Procedure Brand Depth(inches) A(page 16) FRIEDRICH USC 16-23/32 B (pages 17~18) White-Westinghouse Frigidaire Carrier (52F series) 16, 17-1/2 or 22 General Electric /Hotpoint 16-7/8 Whirlpool 17-1/8 or 23 Carrier (51S series) 18-5/8 C (pages 19) Fedders/Emerson Friedrich WSC 16-3/4 or 19-3/4 Emerson/Fedders 15 6 Install new unit into wall sleeve. CAUTION: When installation is completed, replacement unit MUST have a rearward slope as shown. To achieve 1/4" slope, remove the backing from the 11-13/16" shim strips and attach them as shown below in Fig. 19. Place the higher portion of shim to the front of the rib on base of wall sleeve. Brand Wall Sleeve Dimensions (inches) 1/4" Wall Sleeve FRONT UNIT SHIM PLACEMENT UNIT INSTALLATION 1" high 3/4" High Shim 6" 6" FIG. 19 Width Height Depth White-Westinghouse Frigidaire Carrier (52F series) 25-1/2 15-1/4 16, 17-1/2 or 22 General Electric /Hotpoint 26 15-5/8 16-7/8 Whirlpool 25-7/8 16-1/2 17-1/8 or 23 Fedders/Emerson Friedrich WSC 27 16-3/4 16-3/4 or 19-3/4 FRIEDRICH USC 25-7/8 15-17/32 16-23/32 Emerson/Fedders 26-3/4 15-3/4 15 Carrier (51S Series) 25-3/4 16-7/8 18-5/8 —14— PROCEDURE A Install the new unit into the wall sleeve. If you are using the new sleeve (optionally supplied with your unit),skip to step 3. Otherwise, install the plastic grille from the kit. 4 5 Toassembletrim,tp...

Herunterladen

Geben Sie zwei Ziffern: