Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Danby Dateigröße: 410.04 kb Dateiname: Unterrichtssprache:

2) Mode. 3) Fan Speed. 4) Energy Saver. 5) Auto-Timer. 6) Used to increase or decrease temperature settings in 1° increments on the Celsius or Fahrenheit scale. • For the unit: The control is capable of displaying temperaturein degree Fahrenheit or degree Celsius. To convert from one to the other, press and hold the left and right Temp/Timer buttons at the same time for 3 seconds. • For the Remote Control: The control is capable of displaying temperature in degree Fahrenheit or degree Celsius. To convert from one to the other, press and hold the up and down Temp/Timer buttons at the same time for 3 seconds. 7) Cancels current Timer ON/OFF settings. 8) Lock prevents the remote control settings from inadvertently being changed. 9) Clock: Depress the button for 3 seconds in order to set the clock. Press the increase or decrease arrow toadjust the clock in 1 minute intervals, holding down the increase or decrease arrow will adjust the time in 10 minute intervals. 10) Used to activate the SLEEP program. 11) Toggle the LED backlight on/off. 12) Restore remote control default settings. To operate the hand held remote control will require two “AAA” Alkaline batteries (included ). BATTERIES SHOULD BE REPLACED WHEN: a) No signal (beep) is heard when attempting to program the main unit. b) The main unit does not respond to a command issued by the remote control. Battery replacement: 1) Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently) until the cover separates completely from the unit. 2) Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the battery chamber (+/-). 3) Re-install rear cover. 4) If the remote control will not be used for extended periods of time (vacations etc.), batteries should be removed. The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main unit. Any obstruction between the receiver and remote may cause signal interference, limiting the ability to program the main unit. 7 CARE AND MAINTENANCE CLEANING: When cleaning the air conditioner, be sure to turn the SELECTOR knob to the OFF position and disconnect the power cord from the electrical outlet. 1) DO NOT use gasoline, benzene, thinner, or any other chemicals to clean this unit, as these substances may cause damage to the finish and deformation of plastic parts. 2) Never attempt to clean the unit by pouring water directly over any of the surface areas, as this will cause deterioration of electrical components and wiring insulation. AIR FILTER: If the air filter becomes clogged with dust, air flow is obstructed and reduces efficiency. The air filter should be cleaned every 2 weeks. AIR FILTER REMOVAL: The air filter is located behind the air intake front grill. To remove the air filter, grasp the sides of the front grill and pull forward to open and access the filter. To reinstall the air filter, reverse the above procedures. The air filter may be vacuumed or washed by hand in warm water. Dry thoroughly before re-installing. CLEANING AIR FILTER: 1) Use a vacuum cleaner with soft brush attachment 2) Wash the filter in lukewarm water below 40°C (104°F): To get best results, wash with soapy water or a neutral cleaning agent. 3) Rinse the filter with clean water and dry thoroughly before re-installing. IMPORTANT: DO NOT forget to install the air filter. If the air conditioner is left to operate without the air filter, dust is not removed from the room air and may result in machine failure. When the air inlet grill and cabinet are dirty, wipe with lukewarm water (below 40°C). Use of a mild detergent is recommended. END OF SEASON CARE: 1) Operate the fan alone for half a day to dry out the inside of the unit. 2) Turn off power and remove plug from wall socket. 3) Clean filter. 4) Store (covered) air conditioner in a dry location. CAUTION: When installing and/or removing the air conditioner from the window, ensure that caution is taken to prevent it from falling backward. It is recommended that installation or removal of the air conditioner is done with assistance to prevent injury to persons or damage to the unit or property. 8 TROUBLESHOOTING Occasionally, a problem may occur that is minor, and a service call may not be necessary. Use this troubleshooting guide for a possible solution. If the unit continues to operate improperly, call an authorized service depot or Danby’s Toll Free Number for assistance: 1-800-26 (1-800-263-2629) PROBLEM POSSIBLE CAUSE SOLUTION 1) Air conditioner will not operate. • No power to the unit. • Check connection of power cord to power source. • Check fuse or circuit breaker. • Set SELECTOR SWITCH to position other than “OFF”. • The power cord “RESET” button must always be pushed in (engaged) for correct operation. 2) Inefficient or no cooling. • Dirty air filter. • Unit size inappropriate for application • Blocked air flow. • Power interruption, settings changed too quickly, or compressor overload tripped. •...

Herunterladen

Geben Sie zwei Ziffern: