Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
• Install the room air conditioner on the shady side of your home. A window that faces north is best because it is shaded most of the day. • Close the fireplace damper, floor and wall registers so cool air does not escape up the chimney and into the duct work. • Keep blinds and drapes in other windows closed during the sunniest part of the day. • Clean the air filter as recommended in the section “Care and Cleaning.” • Proper insulation and weather stripping in your home will help keep warm air out and cool air in. • External house shading with trees, plants or awnings will help reduce the air conditioner’s work load. • Operate heat producing appliances such as ranges, washers, dryers and dishwashers during the coolest part of the day. 4 SZ000400(En)-Yaokong 4 12/10/2004, 5:36 PM To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Operation of Current Device The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner. 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out. 3. Press the RESET button. Again you will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head). NOTES: • Do not use this device to turn the unit on or off. • Always make sure the RESET button is pushed in for correct operation. • The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. • If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. Multi-Step Fan and Cooling Speeds: Key Features 90 distinct fan settings give the ultimate in airflow and noise control. Low Voltage Compensation: (On some model) Ensures aganist evaporator freeze-ups at low supply voltage conditions. Air Conditioner Features ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote. LIGHT ADJUSTS ON/OFF TEMPERATURE OR TIME ACTIVATES TIMER ADJUSTS TEMP & TIMES FAN CHECK FILTER SPEEDS RESET BUTTON SETS MODES SETS MODE ACTIVATES TIMER REMOTE CONTROL UNIT CONTROL 5 DISPLAYS TEMPERATURE/TIME FAN SPEED SETS FAN SPEEDS AUTO COOL FEATURE SLEEP MODE TURNS UNIT ON OR OFF SZ000400(En)-Yaokong 5 12/10/2004, 5:36 PM NOTE: The following instructions represent the Unit Controls, the sameAir Conditioner Features instructions can be used for the Remote Control. (continued) TO TURN UNIT ON: YOU WILL SEE: DO THIS: PRESS ON/ OFF BUTTON TO CHANGE TEMPERATURE YOU WILL SEE: SETTING: DO THIS: PRESS TO RAISE PRESS TO LOWER Note: Tap or hold either up( ) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 60°F (16°C) and 90°F (32°C). If you want the display to read the actual room temperature. See “To Operate on Fan Only” section on Page 7. ) or down( TO ADJUST FAN SPEEDS: YOU WILL SEE: DO THIS: PRESS TO SELECT: FASTER SLOWER A 2 Digit Display is used to indicate the Fan Speed setting, from 10 through 99. When the “SLOWER” button is pressed the motor speed will slow down at multiple intervals (90 distinct settings), to a minimum setting of 10. To speed the motor up, press the “FASTER” button. The speed will increase at multiple intervals to a maximum setting of 99. After 5 seconds the control will automatically change back to displaying the set temperature. 6 SZ000400(En)-Yaokong 6 12/10/2004, 5:36 PM Air Conditioner Features (continued) TO USE AUTO COOL FEATURE: YOU WILL SEE: DO THIS: PRESS AUTO COOL BUTTON LIGHT On Note: Fan starts at High Speed and adjusts to a slower speed as the room temperature dictates. For example if the room doesn’t get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. Press either the fan slower or fan faster button to adjust the fan speed manually. TO OPERATE ON FAN ONLY: YOU WILL SEE: DO THIS: PRESS MODE BUTTON CHOOSE FAN ONLY LIGHT On Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air(on some models). (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. During this function, the display will show the act...