Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
To change the set temperature, press “COOL” then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Turning the unit “ON” or “OFF” at any timer will cancel the Delay Start/Stop function. The delay Start/Stop feature will work until the unit either starts or stops. Once this has happened then the above steps have to be repeated again. 7 Air Conditioner Features(continued) LIGHT ON SLEEP FEATURE: Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only DO THIS: PRESS SLEEP PAD Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only YOU WILL SEE: The Sleep Mode can be selected with a Heating or Cooling Mode. Note: In this “MODE” the selected cooling temperature will increase by 2 degrees F, 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F, after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. If this Mode is selected with Heat, the set temperature will Decrease at the same time pattern. This ends the “Sleep” MODE and the unit will continue to operate as originally programmed. The “Sleep” MODE program can be cancelled at any time during operation by pressing “Sleep” MODE button. LIGHT ON CHECK FILTER FEATURE: Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only DO THIS: PRESS TO RESET Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only YOU WILL SEE: Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Clean Filter” button and the light will go off. REMOTE SENSING FEATURE (on some models) YOU WILL SEE: Temp/Timer Fan Faster Fan Slower Temp/Timer Cool Energy Saver Fan Only Sleep Auto Temp Timer Start Stop Remote Sensing LIGHT Pulsing On & Off Intermittently DO THIS: PRESS SENSING START BUTTON Note: unit display show “set” temperature Note: remote display is actual temperature at remote control only Note: This feature can be activated from the remote control ONLY . Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only Temp/Timer Fan Faster Fan Slower Temp/Timer Cool Energy Saver Fan Only Sleep Auto Temp Timer Start Stop Remote Sensing To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing start button. The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. It will continue to send this signal until the feature is deactivated by pressing the remote sensing stop button. If the unit does not receive the remote sensing signal during any 3 minute interval, the unit will keep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY . The unit display indicates the set temperature. 8 Air Conditioner Features (continued) HEATING FEATURE (on some models): YOU WILL SEE: Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only DO THIS: PRESS MODE BUTTON SELECT HEAT Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only Note: This feature can be used with any combination of FAN Speeds, Timer, or Sleep Modes. When in the “Heat” Mode, the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between 55°F (13°C) and 80°F (27°C). When the room set temperature is satisfied, the fan will cycle off and on to circulate and sample the room air. TO TURN UNIT OFF: YOU WILL SEE: Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only DO THIS: PRESS ON/OFF BUTTOT Check FilterSleep Temp/Timer Temp/Timer Remote Sensing Timer Mode Fan Speed Auto Temp Med Hi Lo Heat Energy Saver Cool Fan Only FAULT CODES C h e c k F t e r S e e p T e m p /T m e r T e m p /T m e r R em o te S e ns i ng T m e r M o d e F a n S p e e d A uto Temp Med Hi L o Heat E nergy S aver C ool F an Only C h e c k F t e r S e e p T e m p /T m e r T e m p /T m e r R e mo te S e ns i n g T m e r M o d e F a n S p e e d A uto Temp Med Hi L o Heat E nergy S aver C ool F an Only C h e c k F t e r S e e p T e m p /T m e r T e m p /T m e r R e mo te S e n s i n g T m e r M o d e F a ...