Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
2). • CLOSELY SUPERVISE ANY CHILDREN AND PETS WHEN THE UNIT IS IN USE. • THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING ITS USE BY A PERSON RESPONSIBLE FOR THEIR SAFETY. CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE. ELECTRICAL SAFETY: • THIS APPLIANCE IS FOR INDOOR USE ONLY. • ALWAYS TURN OFF THE UNIT AND UNPLUG IT WHEN NOT IN USE. • DO NOT USE THIS UNIT IN EXCESSIVELY HUMID OR WET ENVIRONMENTS (FIG. 3). • DO NOT PULL OR PLACE STRAIN ON THE POWER CORD WHEN MOVING THE APPLIANCE. • IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY AN ELECTRICIAN OR SPECIALIZED TECHNICIAN AUTHORIZED BY THE MANUFACTURER IN ORDER TO PREVENT FIRE. FOR MAXIMUM EFFICENCY: • Make sure doors and windows are closed while the portable air conditioner is in use. Also keep curtains and blinds closed during the sunniest parts of the day while the air conditioner is in operation. • Frequently clean the portable air conditioner’s filters. • Once the room or area has reached your desired comfort level, be sure to reduce the unit’s temperature and ventilation settings. FIG. 1 FIG. 2 k0045 1 k0045 PARTS LIST Front: 1. Control panel 2. Louvers 3. Carrying handle 4. Casters Accessories: 10. Exhaust hose 11. Hose adaptor (goes over the hose and into the window kit) 12. Extendable window kit 13. Activated carbon filter 14. Hose for continuous drainage 15. Remote control Back: 5. Air filter 6. Air inlet 7. Cord storage 8. Exhaust air outlet 9. Rubber plug / drainage point 2 k0045 INSTALLATION INSTRUCTIONS Installing the Exhaust Hose and Window Kit: Wall or Window Adapter FIG.6 1. Open the window and insert the window kit into the open gap. 2. Close the window until the window kit is held securely. This technique may also be used for sash windows. 3. Fit the exhaust hose into the exhaust air outlet located on the back of the air conditioner. 4. Attach one end of the hose adapter onto the exhaust hose. 5. Attach the other end of the hose adapter to the window kit. , Window Kit Œ FIG.5 3 k0045 Positioning the Exhaust Hose: • Insert the exhaust hose into the back of the unit and tighten it into place. • Avoid kinks and bends in the exhaust hose. This can cause moist air to accumulate, resulting in overheating and unexpected shut offs. • The exhaust hose may be extended from 12 inches (300 mm) to 59 inches (1500 mm), but for maximum cooling efficiency, use the shortest hose length possible. WARNING! The included exhaust hose is specifically designed to fit the specifications of this unit. Do not extend it with your own hose, as this can cause the air conditioner to malfunction. FIG.7 FIG.8 FIG.9 FIG.10 4 Installing the Activated Carbon Filter: 1. Remove the filter frame from the unit. 2. Separate the filter from the filter frame. 3. Remove the activated carbon filter from its plastic bag. 4. Insert the activated carbon filter into the filter frame. 5. Reattach the filter onto the filter frame. 6. Insert the filter set into the unit. riff w 2 ViSI CO Bffl ppp^ fS 5 fitH FIG.11 k0045 5 k0045 OPERATING INSTRUCTIONS Control Panel FIG.12 1. Fan speed (ventilation) button 12. 2. Timer button 13. 3. Display window 14. 4. Remote control receiver 15. 5. Heater indicator (for AC-12000H only ) 16. 6. Mode selection button 17. 7. Automatic mode indicator 18. 8. Cooling mode indicator 19. 9. Fan mode indicator 20. 10. Temperature increase button 21. 11. Temperature decrease button 22. Power indicator Full water tank indicator ON/OFF (power) button Sleep mode button Ionizer button Compressor indicator Ionizer indicator Sleep mode indicator Timer indicator Low fan speed indicator High fan speed indicator Turning the Unit On and Off: • Press the ON/OFF button. The unit will automatically begin operating in cooling mode on low fan speed. The default temperature is 75 o F. • At this time, the indicator lights will show any functions that are in progress. Please note that the display window will only show ambient room temperatures ranging from 32o F to 122° F. • To turn the unit off, press ON/OFF button again. 6 k0045 Setting the Mode/Function: 1. Press the MODE button to select the desired mode (cooling, fan or heating). Heating mode is only available on the AC-12000H. 2. The selected mode’s indicator light will turn on. Setting the Temperature: 1. Press the “Up” or “Down” button to change the set temperature. 2. The display window will indicate the set temperature. If no temperature is set, the display will show the ambient room temperature. 3. Please note that the preset temperature for cooling is 75 o F for cooling and 68 o F for heating. Setting the Fan/Ventilation Speed: Press the SPEED button to select the desired fan speed (high or low...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - NEWAIR AC12000H (1.56 mb)