Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
003 PN: 610200094 ESD Warning Before handling the I35MB, or any media associated with the I35MB, ensure that you are working in an ESD-safe environment. Notice This manual describes the features of the Adtron I35MB. Adtron reserves the right to modify, amend, or in any way change the contents and/or products described herein, at any time, without notification. The information contained in this document is provided for reference only. Adtron Corporation does not assume any liability arising out of the application or use of the products described herein. This document may contain or reference information or products protected by copyrights or patents and does not convey any license under the patent rights of Adtron Corporation, nor the rights of others. Errors in this document may be reported in writing to the following address: Adtron Corporation 4415 E. Cotton Center Blvd. Phoenix, AZ 85040 Tel: 602-735-0300, Europe +41-56-496-5640 Fax: 602-735-0359, Europe +41-56-496-5648 techsupport@adtron.com Adtron Corporation is an ISO 9001:2000 certified company. Adtron logo is a trademark of Adtron Corporation. All other names mentioned are trademarks, registered trademarks, or service marks of their respective companies. .2006 Adtron Corporation. All rights reserved. Table of Contents Introduction 1 I35MB Features 1 Related Documents 2 I35MB Jumper Settings 2 Setting Master/Slave and Cable Select 3 Setting a Remote-Mounted Activity LED 3 Interface Connectors 4 I35MB Installation 4 Introduction 4 Inserting the I35MB 5 Removing the I35MB 6 Basic Operation 6 Partitioning and Formatting 6 Operating System Installation 6 I35MB LEDs and Mirror Control Buttons 7 Mirror Control Button Functions 8 Advanced Operations 8 Managing Faults 8 Bank Hard Faults 9 Bank Soft Faults 9 Turning the Buzzer Off 10 Changing Media 10 Resetting Mirroring Indicators 12 Rebuilding a bank 13 Rebuilding a Bank Off-line 13 Using Different Size Media 13 Aborting a button press Using the I35MB Rail Kit 15 S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) Attributes 16 S.M.A.R.T Attribute Table 17 S.M.A.R.T Attribute Notes 18 LED Indicators 19 IDLE State – No host access 19 ACTIVE State – Host access 20 I35MB Dimension Drawings 21 Appendix I 22 Sales and Technical Support 23 Standard Warranty 23 Revision Control 24 i Rev. 003, PN: 610200094 Adtron I35MB Operations Manual Introduction The Adtron™ Diskpak™ Model I35MB with Adtron ActiveRAID™ technology incorporates RAID-1 mirroring in a 3.5-inch hard disk form factor. RAID-1 mirroring between two hard disk drives provides data redundancy and rebuild independent from the host CPU. With both disk drives functioning properly, the I35MB keeps both disk drives automatically updated. If one of the drives fails, the system continues to operate on a single disk drive until the I35MB is removed from the chassis and the failed drive is replaced. When the I35MB is reconnected and powered up, a rebuild can be initiated on the I35MB concurrent with host activity. Once the rebuild is manually started, it continues unattended until complete. ActiveRAID technology significantly reduces the probability of a data storage failure causing an overall system failure. Power Connector IDE Jumper Options Bank 1 Bank 0 40-pin Connector Figure 1 I35MB LEDs, Buzzer, and Mirror Control buttons Flex Cable I35MB Features • Adtron ActiveRAID™ technology, featuring RAID-1 mirrored disk drives independent of host CPU • ATA/ATAPI-5 ANSI NCITS340-2000 compliant; supporting PIO, Multiword DMA, and Ultra DMA interfaces and transfer rates • Standard IDE 40-pin connector, high speed parallel ATA interface • S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) Attributes (Refer to the section of this manual titled S.M.A.R.T. Attributes for more information) • Audio and visual indicators warn of faults • Operator initiated, automatic rebuild functions transparent to the host CPU • Host operations continue with a single faulted disk drive or during a rebuild • Full error detection and management without host intervention • Field upgradeable firmware prevents future obsolescence 1 Rev. 003, PN: 610200094 Adtron I35MB Operations Manual Related Documents • ANSI NCITS 340-2000 ATA/ATAPI-5 Specification • I35MB Product Specification • I35MB Installation Manual Static Sensitive – The I35MB is a static sensitive device. While setting jumpers, take precautions to ensure that static does not discharge into the I35MB. I35MB Jumper Settings The master/slave and remote LED jumper is located on the front of the I35MB, between the IDE and power connectors. This jumper is used to set master, slave, cable select configurations and to mount a remote Activity LED. Refer to Figure 2 for the location of this jumper. The following figure shows the jumper location on the I35MB: IDE jumper options Power connector 40-pin connector 40 2 4 1 5 1 6 2 39 1 Figure 2 I35MB Jumper Locations 2 Rev. 003, PN: 610200094 Adtron I35MB Operat...