Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
If the fifth set of LEDs fails, it can be indicating a faulty front cooling fan control board condition. Remove the control board and send it back to your dealer. Message LED Description Green: Power LED Yellow: Hard Disk Access LED Red: Hard Disk Status LED Power LED Status LED Description off off Power subsystem OK and ready for hard drive insertion on off Hard disk drive is ready for operation on on Hard disk drive failure (*) on fast flash RAID is rebuilding (*) on slow flash Hot-spare hard disk drive ready (*) fast flash on Hard disk drive failure/short circuits fast flash fast flash Fan failure * Must be provided by RAID controller’s SAF-TE function. AP 3000 Hardware Reference Guide 31 IV. Hardware Front Cooling IV. Hardware Setup • 4-11. SCSI Backplane IV. Hardware Setup SCSI Backplane The SCSI backplane of this server is comprised of one SCSI board (DABP5) with Ultra2 SCSI connectors, power inputs, and SCSI ID dip switches. This configuration allows Ultra2 SCSI SCA hard disk drives to be docked into the server. The SCSI board (DA-BP5) does not have auto termination, therefore the included terminator block must be used on the end connector. SCSI Backplane SCSI ID Select DIP Switches Front Side Connects to a SCSI controller through PWR3 the Ultra2 cable Connector PWR2 Connector PWR1 Connector The provided terminator must be placed on this bot- SMB Out Fan Connector tom SCSI connec- SMB In tor. SCSI Backplane Back Side 1” Tray Connector #5 1.6” Tray 1” Tray Connector #5B Connector #4 Fan Control Board Connector 1” Tray 1.6” Tray Connector #3 Connector #3B 1” Tray Connector #2 1” Tray 1.6” Tray Connector #1 Connector #1 AP 3000 Hardware Reference Guide 32 IV. Hardware Setup • 4-12. SCSI ID Setting SCSI ID settings are made through DIP switches located on the SCSI board. The SCSI board has four dip switches to set the hard drive’s power-ON delay and SCSI ID. SCSI ID Setting IDSEL1 IDSEL0 Slot1 Slot2 Slot3A/3B Slot4 Slot5A/5B off off Reserved on on 15 12 11 8 3 on off 14 9 6 4 1 off on 13 10 5 2 0 (*) (*) Default Hard Disk Drive Power On Delay RMT_START DLY_START Description off off Motor (spin) up when powering on on off Motor (spin) up after START UNIT command off on Motor (spin) up after 12xSCSI ID ms on on Reserved (*) (*) Default SCSI ID Dip Switches ON DLY_START RMT_START IDSEL 1 Default setting IDSEL 0 ON DLY_START on RMT_START off IDSEL 1 off IDSEL 0 on 1 2 3 4 1 2 3 4 IDSEL1 IDSEL0 Slot1 Slot2 Slot3A Slot4 Slot5AON IDSEL 1=off IDSEL 0=off off off Resv. ON IDSEL 1=on IDSEL 0=on on on 15 12 11 8 3ON IDSEL 1=on IDSEL 1=off on off 14 9 6 4 1ON IDSEL 1=off IDSEL 0=on off on 13 10 5 2 0 AP 3000 Hardware Reference Guide 33 IV. Hardware SCSI ID Setting IV. Hardware Setup SCSI ID Dip Switches (Cont’) IV. Hardware Setup Expansion Card Stabilizer IDSEL1 IDSEL0 Slot1 Slot3B Slot5BON IDSEL 1=off IDSEL 0=off off off Resv. ON IDSEL 1=on IDSEL 0=on on on 15 11 3ON IDSEL 1=on IDSEL 1=off on off 14 6 1ON IDSEL 1=off IDSEL 0=on off on 13 5 0 NOTE All SCSI devices must have a SCSI identification number that is not in use by any other SCSI device. SCSI devices vary in how they set the ID number. Refer to the product manual for any additional devices that you may install for details on how to set its ID number. • 4-13. Expansion Card Guide The chassis provides an adjustable expansion card guide to help hold expansion cards in their slots. Securing Expansion Card Guide The expansion card guide is mounted by four screws on the top and bottom edge of the chassis. There are 18 knobs on the stabilizer. Turn the knob over the appropriate expansion card counterclockwise to extend the metal arm under each knob. Keep turning until the arm is firmly pressed against the expansion card. Turn the knob clockwise to retract the metal arm. Knob Metal Arm AP 3000 Hardware Reference Guide 34 IV. Hardware Setup • 4-14. SCSI Termination Terminating the SCSI bus “chain” is necessary for SCSI devices to work properly. Ultra2 devices do not have termination jumpers and must be terminated using a terminator on the SCSI cable which means you cannot Female Terminator for SCSI cable Male Terminator for SCSI Board connect a device on the last connector. • 4-15. Power Supply Power Supply Mounting Mounting and unmounting the power supply must be done from the inside. Four screws are used to secure the power supply to the chassis back side. IV. Hardware SCSI/Power AP 3000 Hardware Reference Guide 35 IV. Hardware Setup Power Supply Information Output Voltage Regulation, Ripple, and Noise IV. Hardware Setup Power Supply Info Output Voltage Limits (Vdc) Ripple/Noise Output Min Nom Max Maximum 1 3.17V 3.30V 3.46V 50mV p-p 2 4.80V 5.00V 5.25V 50mV p-p 3 11.40V 12.00V 12.60V 120mV p-p 4 -4.50V -5.00V -5.50V 120mV p-p 5 -10.92V -12.00V -13.20V 120mV p-p 6 4.75V 5.00V 5.25V 50mV p-p Output Current Capacity Output Nom (Vdc) Max (A) Min (A) 1 3.3V *20.0 1.0 2 5.0V *45.0 2.0 3 12.0V 12.0 0.5 4 -5.0V 0.5 0.0 5 -12.0V 0.5 0.0 * Total output power for 3.3V and 5...