Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
PC Desktops - HP Compaq dx2708 Desktop PC (389.51 kb)
PC Desktops - HP Compaq dx2708 Desktop PC (382.48 kb)
Anleitung Zusammenfassung
Miscellaneous cable kit
435309-001
*
1. Hard Disk Drive cable - 280mm (SATA connector) x 1
Deleting a Password
*
2. Optical drive cable x 1, 380mm - SATA
1.
Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart the Computer. To delete
*
3. Diskette drive cable x 1, 200mm
the setup password, run Computer Setup (F10).
*
RJ11 cable
198220-005
2.
When the key icon appears, type your current password followed by a slash (/) or alternate delimiter character as
shown. Example: currentpassword/
* Not shown
3.
Press the Enter key.
DIMM 2
DIMM 3
Clearing CMOS*
CPU XU1
DIMM 1
The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS
CPU_FAN
DIMM 4
memory using by performing the following procedure:
Ä CAUTION: The power cord must be disconnected from the power source before changing the jumper
setting. (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board
1.
Turn off the computer and any external devices, then disconnect the power cord from the power outlet.
2.
Remove the access panel.
3.
Clear CMOS with header J1.
4.
Replace the access panel.
5.
Connect the power cord to the power outlet.
6.
Turn on the computer, allow it to start.
PWR P8
NOTE: Clearing CMOS clears all passwords.
FLOPPY
SYS_FAN
Diagnostic LEDs
P5
LED
Color
LED Activity
State/Message
Power
Green
On
(S0) Computer on
Power
Green
1 blink every 2 seconds
(S1) Normal Suspend Mode
PCIE X 1
Power
Green
1 blink every 2 seconds
(S3) Suspend to RAM
Power
Clear
Off
(S4) Suspend to Disk (if applicable)
PCI 1
Power
Clear
Off
(S5) Computer off
XBT1
PCI 2
Power
Green
Green when flashing ROM
Boot block recovery w/Embedded Video
CLEAR CMOS
JUMPER
Power
Red
Power LED turns into green and CPU thermal shutdown
PCI 3
start to blink two times every
(Weak CPU fan speed or not running)
second, followed by two second
pause.
FRONT PANEL
HEADER
Power
Red
Power LED flashes 5 seconds
No memory installed / Pre-Video memory error
every 1 second, followed by 2
FRONT USB 1
SATA 3
SATA 1
seconds pause, and meanwhile,
FRONT AUDIO
FRONT USB 2
5 beeps are heard.
HEADER
SATA 4 SATA 2
CD_IN AUDIO
Power
Red
Power LED flashes 6 seconds
Graphics card error (Pre-Video graphics error)
every 1 second, followed by 2
seconds pause, and meanwhile,
6 beeps are heard.
System Board Connectors and Jumpers (position of some untitled components may vary in location)
Power
Red
Power LED flashes 8 seconds
System board failure or invalid ROM basing on
every 1 second, followed by 2
checksum.
Label
Component
Label
Component
seconds pause, and meanwhile,
8 beeps are heard.
XU1
Processor socket
Clear_CMOS Clear CMOS header
Hard Drive
Green
Blinking
Hard drive activity
CPU_FAN
CPU fan
J94
Front panel header
DIMM1
Memory socket 1
XBT1
Real-time-clock battery
DIMM2
Memory socket 2
Front_Audio Front audio header
Computer Setup (F10) Utility Features (not all features may be available)
DIMM3
Memory socket 3
CD_in
CD in audio
System S/N
Memory DIMM1
DIMM4
Memory socket 4
PCI 1
PCI 1 connector
Product Name
Memory DIMM2
OwnerShip TAG
Memory DIMM3
FLOPPY
Diskette drive connector
PCI 2
PCI 2 connector
BIOS Version
Memory DIMM4
System
BIOS Release Date
DDR2 Memory Size
Power
ATX main power
PCI 3
PCI 3 connector
Information
System Chipset Type
UUID
SATA1
SATA connector 1
PCIE X 1
PCI-E x1 connector
Processor Type
Chassis Serial Number
Processor Speed
Asset TAG Number
SATA2
SATA connector 2
SYS_FAN
System fan
CPU ID
Integrated MAC
Cache Size
SATA3
SATA connector 3
P5
CPU 4 pin power connector
System Date
Halt On
SATA4
SATA connector 4
System Time
Standard
Floppy Drive A
#See table below
SATA Port 0
CMOS
AGP socket not shown in this drawing
SATA Port 1
Features
SATA Port 2
SATA Port 3
SATA Port 0/1 Working Mode
Quick Power On Self Test
Load Boot Menu Selectable
Clear_CMOS
CMOS
POST Delay Time (seconds)
APIC Mode
Hard Disk Boot Priority
System Keyboard
Clear CMOS
1-2
Advanced
First Boot Device
Boot Up NumLock Status
BIOS Features Second Boot Device
Security Option
Normal (Default)
2-3
Third Boot Device
Fourth Boot Device
Boot Other Device
PEG/Onchip VGA Control
System Hardware Interrupts
Advanced
On-Chip Frame Buffer Size
Chipset
DVMT Mode
IRQ
System Function
IRQ
System Function
Features
DVMT/FIXED Memory Size
Init Display First
1
Keyboard
10
VGA controller
USB Controller
Serial Port
3
USB OHCI (DID:F02)
10
USB OHCI (DIA:F00)
USB Legacy support
Parallel Port
Integrated
HD Audio
Parallel Port Mode
4
Serial Port
10
USB OHCI (DID:F00)
Peripherals
Onboard Lan
ECP Mode Use DMA
Onboard Lan Boot ROM
6
FDC controller
10
Lan controller
Onboard FDC Controller
7
Parallel Port (LPT 1)
11
SATA controller
ACPI Function
ACPI Suspend Type
9
USB OHCI (DIA:F01)
12
Mouse
Power
Restore On AC/Power Loss
9
USB OHCI (DID:F01)
Resume On PME
Management
Resume On Ring
Setup
Resume On Alarm
Date(of Month) Alarm
Time(hh:mm:ss) Alarm
Establishing a Password
PnP/PCI
Reset Configuration Data
1.
Turn on or restart the computer. If you are in Windows, click Start > Shut Down >
Resources Controlled By
Configurations
Restart the computer.
IRQ Resources
2.
When the F10 Setup message appears in the lower-right corner of the screen, press the F10 key. Press Enter to
Reset Case Open Status
bypass the title screen, if necessary. If you do not press F10 when prompted, a restart will be necessary.
CPU Temperature
Hardware
CPU Fan Speed
3.
Select supervisor password and press enter key, and follow the instructions on the screen. You may also want to
Monitor Setup
System Fan Speed
establish the Password check at this time. This will allow you to specify when the password will be required.
CPU Fan Fault Detect
4.
Before exiting, click Save Settings and Exit.
SYS Fan Fault Detect
Load
Optimized
Defaults
Changing a Password
Set
1.
Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart the Computer. To change
Supervisor
the setup password, run Computer Setup.
Password
2.
When the key icon appears, type your current password, a slash (/) or alternate de-limiter character, your new
password, another slash (/) or alternate delimiter character, and your new password again as shown:
Set User
Password
current password/new password/new password.
Save Setting
NOTE: Type the new password carefully since the actual characters do not appear on the screen.
and Exit
3.
Press the enter key.
Exit Without
4.
The new password will take effect the next time the computer is restarted.
Saving
Note: See Computer Setup (F10) Utility Guide on the Library CD.