Anleitung Dell, modell PowerEdge C6100
Hersteller: Dell
Dateigröße: 21.61 mb
Dateiname: 6100HM.pdf
Unterrichtssprache:
|
 
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
7 Apply thermal grease evenly to the center of the top of the new processor. CAUTION: Using excess thermal grease can cause grease to contact the processor shield, which can cause contamination of the processor socket. 8 Place the heat sink on the processor. See Figure 3-8. 9 Using a Phillips screwdriver, tighten the heat-sink retention screws. See Figure 3-8. Installing System Components 10 Replace the cooling shroud. See "Installing the Cooling Shroud" on page 64. 11 Replace the system-board assembly. See "Installing a System-Board Assembly" on page 62. 12 Reconnect the system to its electrical outlet and turn on the system, including any attached peripherals. 13 Press to enter the System Setup program, and check that the processor information matches the new system configuration. See "System Setup Options at Boot" on page 36. Expansion-Card Assembly and Expansion Card Removing the Expansion Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet. 2 Remove the system-board assembly. See "Removing a System-Board Assembly" on page 61. 3 Remove the cooling shroud. See "Removing the Cooling Shroud" on page 63. 4 Remove the five screws that secure the expansion-card assembly. See Figure 3-10. 5 Lift the expansion-card assembly out of the system-board assembly. See Figure 3-10. Installing System Components 70 Installing System Components Figure 3-10. Removing the Expansion-Card Assembly 6 Remove the screw securing the expansion card. Figure 3-11. Removing the Expansion Card 1 screw (5) 2 expansion-card assembly 1 expansion-card slot cover 2 screw 3 expansion card 4 expansion-card connector 1 2 4 1 2 3 7 Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector. 8 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening, and close the expansion-card latch. NOTE: You must install a filler bracket over an empty expansion slot to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. Installing the Expansion Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: Expansion cards can only be installed in the slots on the expansion-card riser. Do not attempt to install expansion cards directly into the riser connector on the system board. 1 Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card. 2 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet. 3 Remove the system-board assembly. See "Removing a System-Board Assembly" on page 61. 4 Remove the cooling shroud. See "Removing the Cooling Shroud" on page 63. 5 Remove the five screws that secure the expansion-card assembly. 6 Lift the expansion-card assembly away from the system-board assembly. 7 Remove the screw securing the filler bracket. Installing System Components 8 Grasp the filler bracket by its edges, and carefully remove it from the expansion-card connector. NOTE: Keep this bracket in case you need to remove the expansion card. Filler brackets must be installed over empty expansion-card slots to maintain FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 9 Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansion-card assembly. 10 Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated. 11 Replace the screw securing the expansion card. 12 Place the expansion-card assembly into the system-board assembly. 13 Replace the five screws that secure the expansion-card assembly. 14 Replace the cooling shroud. See "Installing the Cooling Shroud" on page 64. 15 Replace the system-board assembly. See "Installing a System-Board Assembly" on page 62. 16 Reconnect the system to its electrical outlet and turn on the system, including any attached peripherals. Expansion-Card Connector Removing the Ex...
)