Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
PC Desktops - Aspire G3-605 (1.68 mb)
PC Desktops - Aspire G3-605 (1.67 mb)
PC Desktops - Aspire G3-605 (1.86 mb)
Anleitung Zusammenfassung
The computer uses a state-of-the-art bus architecture, which improves system efficiency and helps the system support varied multimedia and software applications. Your AcerSystem has standard I/O (input/output) interfaces such as a parallel port, PS/2 keyboard and mouse ports, USB ports, and stereo microphone, line-in and line-out jacks (configuration may vary by models). The system can accommodate extra peripheral equipment through these I/O ports. Your system can also support an optional high-speed fax/data modem or an additional LAN (local area network) card. Necessary to know before setup Selecting a location Selecting the optimum location for your computer: • Do not place the system too close to other electrical equipment. • Do not place the system in high-traffic areas or where the power cord or other cords may be stepped on. • Avoid placing the system in any location that is excessively dusty or damp. CAUTION: Please use the foot stand when placing your PC in the upright position. Opening the package Open the package carefully and keep all packing materials for later use. Ensure that all items are present and in good condition. If any of the following items are missing or appear damaged, contact your dealer immediately: • AcerSystem • Mouse (PS/2 or USB) • Keyboard (PS/2 or USB) English English 4 Setting up your computer • Wireless keyboard with pointing function • Remote control Note: Mouse, keyboard, wireless keyboard or remote control configuration may vary by selected models • User's Guide and Starter poster • Other user documentation and third-party software. Connecting peripherals After everything is connected, plug the power cord into the system and insert the other end into a power outlet. Note: Don't connect the system power cord before connecting all peripherals to the system. Starting your computer After connecting all the peripheral equipment, start your computer according to the steps below: 1 Turn on all peripheral equipment, such as the monitor, printer, fax, speakers, etc. 2 Turn on the system. Once the start up process is complete, you can begin to use your computer. Shutting down your computer In the event of a system crash, press and hold the power button on the front of the system for four seconds. After the system has shut down, turn off all peripheral devices. System upgrade (selected models only) You can expand your AcerSystem system quickly and easily by adding components. You can also upgrade the components of your AcerSystem system. 5 Opening the computer Before removing any panels or covers, please make sure to shut off the computer and unplug the power cord from the outlet. • Remove the screws on the chassis. • Slide the panel off. Setting up new components You can only use components compatible with AcerSystem computers. Before you choose new components, please ask your authorized Acer dealer whether the part will operate within your AcerSystem system. In order to ensure proper setup and installation, please refer to the instructions provided with your new components. Probable upgrades are: • Upgrade to high-capacity HDD • Expand high-level memory • Upgrade from a CD-ROM drive to CD-RW, DVD-ROM, DVD/CDRW combo or DVD writer (selected models only) • Install additional interface cards in empty PCI slots, e.g., PCI fax/ modem card (selected models only) English English 6 Frequently asked questions The following questions are possible situations that may arise during the use of your computer and each is followed by easy answers and solutions to the situation. Q: I pressed the power switch but the system did not boot up. A: Check the LED located above the power switch. If the LED is not lit, no power is being applied to the system. Do any of the following: • Check if the voltage selector switch located on the rear panel of the computer is set to the correct voltage. • Check if you plugged the power cable properly into an electrical outlet. • If you are using a power strip or AVR, make sure that it is plugged in and turned on. If the LED is lit, check the following: • Is a non-bootable (non-system) diskette in the floppy drive? If yes, remove or replace it with a system diskette and press Ctrl + Alt + Del to restart your computer. • The operating system files may be damaged or missing. Insert the start-up disk you created during Windows setup into the floppy drive and press Ctrl + Alt + Del to restart your computer. This will automatically diagnose your system and make necessary fixes. However, if the diagnostic utility still reports a problem, then you may have to perform the recovery process to restore your system to its original default factory settings. Note: For more information about recovering your system, refers to the RCD instruction sheet. Q: Nothing appears on the screen. A: Your computer's power management function automatically blanks the screen to save power. Just press any key to turn the display back on. If pressing a key does not work, you can restart your compu...
Dieses Handbuch ist für folgende Modelle:PC Desktops - Aspire T3-605 (428.67 kb)
PC Desktops - Aspire TC-100 (428.67 kb)
PC Desktops - Aspire TC-603 (428.67 kb)
PC Desktops - Aspire XC-105 (428.67 kb)