Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
WARNING: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CHAPTER 7: DRIVES CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To prevent data loss, turn off your computer (see “Turning Off Your Computer” on page 7) before removing the hard drive. Do not remove the hard drive while the computer is on or in Sleep state. CAUTION: Hard drives are extremely fragile. Exercise care when handling the hard drive. NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell or Alienware. NOTE: If you are installing a hard drive from a source other than Dell or Alienware, you need to install an operating system, drivers, and utilities on the new hard drive. 034/034 CHAPTER 7: DRIVES Removing Optical Drive(s) 1. Follow the instructions in “Before You Begin” on page 6. 2. Press the AlienHead to lower the drive panel. 2 1 1 drive panel 2 AlienHead 035/035 CHAPTER 7: DRIVES 3. 4. Lift the release panel and open the left side-panel. Disconnect the power cable and the data cable from the back of the optical drive. 5. Pull the securing tab on the optical-drive bracket and slide the optical drive out through the front of the computer. 1 3 2 4 1 data cable 3 optical drive 2 power cable 4 securing tab 036/036 CHAPTER 7: DRIVES Replacing Optical Drive(s) 1. Follow the instructions in “Before You Begin” on page 6. 2. Remove the new drive from its packaging. Save the original packaging for storing or shipping the optical drive. 3. Remove the optical-drive bay filler, if applicable: Pull the securing tab on the optical-drive bracket and slide the optical-drive bay filler out through the front of the computer. 4. Pull the securing tab on the optical-drive bracket and slide the optical drive into the optical-drive bay, until the securing tab snaps into place. 5. Connect the power cable and the data cable to the optical drive. 6. Close the left side-panel. 7. Connect your computer and devices to electrical outlets, and then turn them on. 037/037 CHAPTER 7: DRIVES Removing the Media Card Reader 1. Follow the instructions in “Before You Begin” on page 6. 2. Press the AlienHead to lower the drive panel. 2 1 1 drive panel 2 AlienHead 038/038 CHAPTER 7: DRIVES 3. 4. 5. Lift the release panel and open the left side-panel. Disconnect the FlexBay cable from the back of the Media Card Reader. Pull the securing tab on the FlexBay bracket and slide the Media Card Reader out through the front of the computer. 1 2 3 1 FlexBay cable 3 securing tab 2 Media Card Reader 039/039 CHAPTER 7: DRIVES Replacing the Media Card Reader 1. Follow the instructions in “Before You Begin” on page 6. 2. Remove the new Media Card Reader from its packaging. Save the original packaging for storing or shipping the Media Card Reader. 3. Remove the FlexBay filler, if applicable: Pull the securing tab on the FlexBay bracket and slide the FlexBay filler out through the front of the computer. 4. Pull the securing tab on the FlexBay bracket and slide the Media Card Reader into the FlexBay, until the securing tab snaps into place. 5. Connect the FlexBay cable to the Media Card Reader. 6. Close the left side-panel. 7. Connect your computer and devices to electrical outlets, and then turn them on. 040/040 CHAPTER 7: DRIVES Removing Hard Drive(s) 1. Follow the instructions in “Before You Begin” on page 6. 2. Lift the release panel and open the right side-panel. 1 3. Press the hard-drive release tabs simultaneously and slide the hard drive towards the top and out of the computer. 2 1 hard-drive release tabs (2) 2 hard drive 041/041 CHAPTER 7: DRIVES 4. If you are removing a solid-state drive (SSD): a. Remove the four screws that secure the SSD to the hard-drive bracket. b. Slide and lift the SSD out of the hard-drive bracket. 1 2 3 1 screws (4) 3 SSD 2 hard-drive bracket 042/042 CHAPTER 7: DRIVES Replacing Hard Drive(s) 1. Follow the instructions in “Before You Begin” on page 6. NOTE: See the documentation that shipped with your new hard-drive to verify that it is configured for your computer. 2. If you are replacing an SSD: a. Replace the SSD in the hard-drive bracket. b. Replace the four screws that secure the SSD to the hard-drive bracket. 3. Slide the new hard-drive into the hard-drive bay and align it with the hard-drive connector. 4. Press the hard drive down until it locks into place. 5. Close the right side-panel. 6. Connect your computer and devices to electrical outlets, and then turn them on. 2 1 1 hard drive2 hard-drive connector 043/043 CHAPTER 8: FRONT BEZEL CHAPTER 8: FRONT BEZEL CHAPTER 8: FRONT BEZEL 044/044 CHAPTER 8: FRONT BEZEL Front Bezel WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory C...