Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Back to Contents Page Replacing the Bottom Logo Assembly Dell™ Studio Hybrid Service Manual Removing the Bottom Logo Assembly Removing the Bottom Logo LED Installing the Bottom Logo LED Installing the Bottom Logo Assembly Removing the Bottom Logo Assembly 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive cage (see Removing the Drive Cage). 4. Remove the processor heat sink (see Removing the Heat Sink). 5. Remove the front I/O panel (see Removing the Front I/O Panel). 6. Remove the back panel (see Removing the Back Panel). 7. Remove the system board (see Removing the System Board). 8. Remove the screw that secures the logo bracket to the chassis. 9. Slide and lift the logo bracket away from the chassis. Removing the Bottom Logo LED 1. Pry the LED away from the chassis using a screwdriver. 2. Lift the LED away from the chassis. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at 3. Disconnect the cable attached to the LED. Installing the Bottom Logo LED 1. Paste the LED between the clamps. 2. Reconnect the cable to the LED. Installing the Bottom Logo Assembly 1. Align the slots on the logo bracket with the tabs on the chassis. Slide the logo bracket until it clicks into position. 2. Replace the screw that secures the logo bracket to the chassis. 3. Replace the system board (see Installing the System Board). 4. Replace the front I/O panel (see Installing the Front I/O Panel). 5. Replace the back panel (see Installing the Back Panel). 6. Replace the processor heat sink (see Installing the Heat Sink). 7. Replace the drive cage (see Installing the Drive Cage). 8. Replace the computer cover (see Installing the Computer Cover). Back to Contents Page NOTE: Ensure that the logo assembly cable does not get entangled during this procedure. Back to Contents Page Replacing Cards Dell™ Studio Hybrid Service Manual Removing the WLAN Card Installing the WLAN Card Removing the Blu-ray Decode Acceleration Card Installing the Blu-ray Decode Acceleration Card Removing the Riser Card Installing the Riser Card Your Dell™ computer provides slots for the following cards: l WLAN card l Blu-ray decode acceleration card l Riser card Removing the WLAN Card 1. Follow the procedure in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive cage (see Removing the Drive Cage). 4. Disconnect the antenna cables from the WLAN card and release the WLAN card by removing the screw that secures the card to the system board. 5. Lift the WLAN card out of its system board connector. Installing the WLAN Card 1. Follow the procedure in Before You Begin. 2. Insert the WLAN card connector at a 45-degree angle into the system board connector labeled "MINI_CARD2." 3. Connect the appropriate antenna cables to the WLAN card you are installing.The WLAN card has two triangles on the label (white and black): l Connect the white antenna cable to the connector labeled "main" (white triangle). l Connect the black antenna cable to the connector labeled "aux" (black triangle). 4. Tighten the screw to fasten the card in place. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: The connectors are keyed to ensure correct insertion. Use of excessive force may damage the connectors. NOTICE: To avoid damage to the WLAN card, ensure that there are no cables under the card. 5. Replace the drive cage (see Installing the Drive Cage). 6. Replace the computer cover (see Installing the Computer Cover). Removing the Blu-ray Decode Acceleration Card 1. Follow the procedure in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive cage (see Removing the Drive Cage). 4. Release the Blu-ray decode acceleration card by removing the screw that secures the card to the system board. 5. Lift the Blu-ray decode acceleration card out of its system board connector. Installing the Blu-ray Decode Acceleration Card 1. Follow the procedure in Before You Begin. 2. Insert the Blu-ray decode acceleration card connector at a 45-degree angle into the system board connector labeled "MINI_CARD1." 3. Tighten the screw to fasten the card in place. 4. Replace the drive cage (see Installing the Drive Cage). 5. Replace the computer cover (see Installing the Computer Cover). Removing the Riser Card 1. Follow the procedure in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive cage (see Removing the Drive Cage). 4. Remove the hard drive (see Removing the Hard Drive). 5. Remove the optical drive (see Removing the Optical D...