Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Secure the PCI card with the screw. 6. Align the riser bracket to the system module. 2 1 5 3 4 4 Hardware Installation - 20 - 2-6 Installing the Hard Disk Drive Read the following guidelines before you begin to install the Hard disk drive: • Take note of the drive tray orientation before sliding it out. • The tray will not fit back into the bay if inserted incorrectly. • Make sure that the HDD is connected to the HDD connector on the backplane. Follow these instructions to Hard disk drive: 1. Lossen the screw securing the hard drive plate. 2. Slide the hard disk plate horizontally to the back and remove the plate in the direction of the arrow. 3. Secure the hard drive to the tray with four (4) screws as shown. Do not over tighten thescrews. Slide the blank into the bay until it locks into place. 1 2 3 - 21 - Hardware Installation 2-7 Removing and Installing the Fan Duct Follow these instructions to remove/install the fan duct: 1. Loosen and remove the screws securing the fan duct. 2. Lift up to remove the fan duct 3. To install the fan duct, align the fan duct with the guiding groove. Push down the fan duct into chassis until its firmly seats 1 2 Hardware Installation - 22 - 2-8 Replacing the FAN Assemblly Follow these instructions to replace the fan assembly: 1. Pull the retaining clip on the side of the system fan along the direction of the arrow 2. Lift the system fan out of the system fan cage. 3. Reverse the previous steps to install the replacement fan assembly. 1 2 - 23 - Hardware Installation 2-9 Replacing the Power Supply Follow these instructions to replace the power supply: 1. Disconnect all the power cables. 2. Remove the four screws securing on the power supply. 3. Lift the power supply out of the chassis in the direction of the arrow. 4. Insert the replacement power supply firmly into the chassis. Connect the AC power cord to the replacement power supply. 1 2 3 Hardware Installation - 24 - Chapter 3 System Appearance 3-1 Front View No. Decription 1 Front USB 2.0 ports 2. Front Panel LEDs and buttons 1 2 3-2 Rear View No. Decription 1 Power module 2. Serial port 3. VGA port 4. RJ-45 LAN ports 5. USB 2.0 ports 6. Full-height riser card bay 1 2 3 4 5 6 3-3 Front Panel LED and Buttons No. Name Color Status Description 1 HDD Status LED Green On HDD access N/A Off Idle 2 Power LED Green On System has power applied to itor ACPI S0 state Green Blink System is in ACPI S1 state (sleep mode) N/A Off System is not powered on or in ACPI S5 state (power off) System is in ACPI S4 state (hlbernate mode) 3 LAN1 LED LED Green On Link between system and network Green Blink access N/A Off No access 4 System Status LED Green On Running or normal peration Green Blink System dedraged due to CPU or DIMM error N/A Off System not ready May indicate the following: • POST error • NMI error • Processor or terminator missing 5. LAN2 LED LED Green On Link between system and network or no access Green Blink Network access N/A Off No access 7 Reset button 8 Power button Green On System is powered on. N/A Off System is powered off. 12367845 -25 -Hardware Installation 3-4 Rear System LAN LEDs No. Name Color Status Description 1 Connection/ Speed LED Orange On Linking at 1 Gbps data rate Green On Linking at 100 Mbps data rate N/A Off Linking at 10 Mbps data rate 2. Activity LED Green Blink Data transmission or receiving is occurring Green On No data transmission 2121 Hardware Installation - 26 - 27 - Hardware Installation Chapter 4 Motherboard Components 4-1 GA-6UASV3-SI Motherboard Components Item 1 USB_ L AN1 2 USB_ LAN2 3 VGA1 4 COM1 SYS_ FAN3 6 CPU_ FAN 7 PWR2 8 PWR_PMB 9 DIMMB2 DIMM B1 11 DIMMA2 12 DIMMA1 13 PWR1 14 SYS_ FAN2 CPU1 16 SYS_FAN1 17 CLR _CMOS 18 SATA0 ~5 19 MFGJMPR COM2 21 USB1 22 USB2 23 USB_ A1 24 CLR _PWD BAT 26 BIOS_RVCR 27 F_ PANEL 28 SGPIO 29 HDD_LED PCI _SLOT1 31 PCIE_SLOT4 Code Description USB connectors and LAN connector USB connectors and LAN connector (BMC Management LAN port) VGA port Serial port System fan cable connector CPU fan cable connector 8 pin power connector IPMB connector DIMM slot (channel B-2 ) DIMM slot (channel B-1 ) DIMM slot (channel A-2 ) DIMM slot (channel A-1 ) 24 pin power connector System fan cable connector Intel LGA1155 socket System fan cable connector Clear CMOS jumper SATA cable connectors ME recovery jumper Serial cable connector USB connector USB connector Type A USB connector Clear passwoed jumper Battery socket BIOS recovery jumper Front panel cable connector SGPIO connector HDD LED connector PCI slot (32bit/33MHz) PCI-E slot 4 (x16 slot) - 29 - Hardware Installation 4-2 Jumper Setting No. Jumper Code Jumper Setting 1. MFGJMPR (ME Recovery Jumper) 1-2 Close: Enable ME recovery. (Default setting) 2-3 Close: Disable ME recovery. 2. CLR_CMOS (Clearing CMOS Jumper) 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear CMOS data 3. CLR_PWD (Clearing Supervisor Password Jumper) 1-2 Close: Normal operation (Default setting) 2-3 Close: Clear supervisor password. 4. BI...