Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Gigabyte Dateigröße: 384.52 kb Dateiname: Unterrichtssprache:

IV. System Component Installation ¦Remove the screws of the side cover of the chassis, push backward to dismount the cover. Remove front panel For different processor types, please refer to below installation guide. .... ¦CPU (For Intel Pentium.and Intel Celeron processors) CPU Pin Lever P. E4 G-MAX Micro ATX Series User’s Manual 1. Insert the CPU on the CPU socket. Before installation, lift up the lever and align the cut of the CPU with the marking on the socket. 2. Pull down the lever to lock the CPU on the socket after installation. When you are installing the heat sink, please make sure to keep the heat sink tight against the CPU to obtain the best cooling result. 3. Apply the thermal compound to one side of the template, and ensure the compound is spread evenly across the template and repeat if necessary. 4. Connect fan power connector to the CPU FAN connector on the motherboard. Click heat sink lock on the CPU socket Install fan on top of CPU . . ¦CPU(For IntelPentium4 processors) CPU Pin Lever 1.Insert the CPU on the CPU socket. Before installation, lift up the lever and align the cut of the CPU with the marking on the socket. 2.Pull down the lever to lock the CPU on the socket after installation. Put CPU cooler on retention module and make sure to keep the heat sink tight against the CPU to obtain the best cooling result. Lock the cooler on retention module. 3. Apply the thermal compound to one side of the template, and ensure the compound is spread evenly across the template and repeat if necessary. 4. Connect fan power connector to the CPU FAN connector on the motherboard. Click the heat sink locker to the motherboard retention module. Install fan on top of CPU P. E5 Install fan on top of CPU Install fan on top of CPU G-MAX Micro ATX Series User’s Manual . ¦CPU (For Intel Tualatin processors) In this section you will find the gist of CPU installation. CPU Pin Lever 1.Insert the CPU on the CPU socket. Before installation, lift up the lever and align the cut of the CPU with the marking on the socket. 2.Pull down the lever to lock the CPU on the socket after installation. Put CPU cooler on retention module and make sure to keep the heat sink tight against the CPU to obtain the best cooling result. Lock the cooler on retention module. 3. Apply the thermal compound to one side of the template, and ensure the compound is spread evenly across the template and repeat if necessary. 4. Connect fan power connector to the CPU FAN connector on the motherboard. Click fan lock on the pin at sides of CPU socket. Set CPU clock frequency from BIOS Setup, see Motherboard Manual for details. For AMD AthlonTM and AMD DuronTM processors, the installation method will be similar .. .. to IntelPentium.and Intel Celeron processors P. E6 G-MAX Micro ATX Series User’s Manual G-MAX Micro ATX Series User’s Manual ¦Memory Notches at sides of module SDRAM Position notches. Make sure that the notches should align the pin on DIMM slot on the motherboard Notches at sides of module DDR Position notches. Make sure that the notches should align the pin on DIMM slot on the motherboard In this section we will guide you to install 168-pin DIMM RAM module. First, make sure the position notches at the bottom of the module should align to the pins on the module sockets on the motherboard, then push the module downward until the locks hook up notches at sides. Locks: make sure they hook up the notches at sides of module P. E7 G-MAX Micro ATX Series User’s Manual G-MAX Micro ATX Series User’s Manual ¦Hard Drive Installation 1.Remove 3 screws in front of the hard drive chassis and dismount chassis. 2.The chassis accommodates up to three 3.5” storage devices. Select a place and fix the hard drive with screws. 3.5”Floppy Drive Hard drives 3.Connect the IDE cable included in the accessory box to the connector on the hard Connect to hard drive drive. Make sure that the RED wire on the ribbon connects to PIN 1 of the hard drive. 4.Connect power connector to the hard drive. P. E8 G-MAX Micro ATX Series User’s Manual 5.Install chassis back to position after completing hard drive installation. 6.Connect the other end of the IDE connector to the IDE-1 bus on the motherboard. 7.Check all connections again. Put back side panel Put back front panel P. E9 G-MAX Micro ATX Series User’s Manual V.System Installation and User’s Guide ¦Front Panel Floppy CD-ROM Slot CD-ROM Eject Button Floppy LED Power LED Floppy Drive Power Button Eject Button HDD LED LINE OUT USB Hub *PCMCIA Port *USB Hub MIC IN *PCMCIA Button *1394 Hub Notice!! A. For those models with front audio module: B. If you use microphone for recording, please insert it in the Front Audio Port. MIC IN USB HUB LINE OUT G-MAX Micro ATX Front Audio Port P. E10 G-MAX Micro ATX Series User’s Manual ¦Rear Panel .. .. 1. For Intel Pentium.and Intel Celeron, AMD AthlonTM and AMD DuronTM motherboard solution. Power Socket Voltage Switch Keyboard Port(PS/2) Mouse Port(PS/2) *LAN Port USB Hub COM Port LPT Port ...

Herunterladen

Geben Sie zwei Ziffern: