Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
3 Select the application that you want to reinstall. 4 Follow all onscreen instructions until you finish the installation. English EnglishEnglish 40 3 System utilities Recovering your system If your operating system files are lost or damaged, the recovery process will restore your system's original factory default settings or last system backup. Your Veriton series computer includes an OBR(One Button Recovery) button, a feature that makes restoring your system quick and easy. OBR works from a hidden partition on your hard drive that contains all the information required to restore your system. There are two modes to recovery your system. One is from system’s original settings and another is from system backup. You can press Alt + F10 after the BIOS finishes running the Power On Self Test (POST). Warning: Initiating the recovery operation while the operating system is running will result in abnormal shutdown and may make your current OS unstable or unusable. After the POST runs, Press Alt + F10 combine key during BIOS to enter hidden partition. This utility has same password protection with Acer eRecovery. Follow all onscreen instructions. 41 You can also follow the steps below: 1 Locate the OBR button. 2 Press the button. You can change the password in Acer eRecovery. a If you have not yet backed-up your system. English EnglishEnglish 42 3 System utilities b If you have previously backed-up your system. 3 Select “Recover to Default Settings” to restore your system to the default factory settings. Select “Recover data from last backup” to restore your system to the last system backup. 43 If you chose the recovery option, you should see the following screen. Click OK to continue. English After 15 seconds the system will reboot and initiate the restore operation. EnglishEnglish 44 3 System utilities 6 After the recovery operation finishes the system will reboot. You will be required to go through the setup process again. Caution! Running the Recovery operation will erase all files previously saved in your computer so make sure to back up your important files before starting the recovery process. Note : This feature occupies 4GB in a hidden partition on your hard drive. If you attempt to restore your system using the One Button Recovery feature, and the system DOES NOT respond, contact your local vendor or authorised Acer representative immediately. 4 Frequently asked questions This chapter tells you what to do in case your computer is not working properly. However, if a more serious problem arises, contact your dealer or the technical support center (for assistance. 47 Frequently asked questions The following questions indicate possible situations that may arise during the use of your computer and each is followed by easy answers and solutions. I pressed the power switch but the system did not boot up. Check the LED located above the power switch. If the LED is not lit, no power is being applied to the system. Try the following: • Check if you properly plugged the power cable into an electrical outlet. • If you are using a power strip or AVR, make sure it is plugged in and turned on. If the LED is lit, check the following: • Is a nonbootable (nonsystem) diskette in the floppy drive? If yes, remove or replace it with a system diskette and press to restart your computer. • The operating system files may be damaged or missing. Insert the startup disk you created during Windows setup into the floppy drive and press to restart your computer. This will automatically diagnose your system and make necessary fixes. However, if the diagnostic utility still reports a problem, then you may have to perform the recovery process to restore your system to its original default factory settings. Note: For more information about recovering your system, see "Acer eRecovery Management" on page 11. Nothing appears on the screen. Your computer's power management function automatically blanks the screen to save power. Just press any key to turn the display back on. If pressing a key does not work, you can restart your computer. If restarting your computer does not work, contact your dealer or technical support center for assistance. English EnglishEnglish 48 4 Frequently asked questions The printer does not work. Do the following: • Make sure the printer is connected to a power outlet and that it is turned on. • Make sure the printer cable is connected securely to the system's parallel or USB port and the corresponding port on the printer. • For additional information concerning the printer, refer to the printer's documentation. No sound comes out from the computer. Check the following: • The volume may be muted. Look for the Volume icon on the taskbar. If it is crossed-out, click on the icon and deselect the Mute option. You can also press the volume control/mute knob on your USB keyboard to toggle from mute to sound on. • If headphones, earphones or external speaker...
PC Desktops - Veriton 1000 (4.26 mb)