Stimmen - 5, Durchschnittliche Bewertung: 4.4 ( )

Hersteller: Dell Dateigröße: 1.19 mb Dateiname: Unterrichtssprache:

If they are correct, they can be accepted by pressing the [Return] key. An error occurs if you set the address of the Service Processor or a domain to a value that either is out of range for a previously configured network address, or conflicts with an address already assigned to another domain or the Service Processor. You can override such errors by using the -f option. Using the -f option with a conflicting IP address may cause misconfiguration. You must resolve such conflicts for DSCP to operate properly. With no arguments, setdscp enters an interactive mode that prompts you to enter all of the DSCP IP address information sequentially. (The noninteractive method, setting up the IP addresses of all domains using the -i and -m options, is preferred.) After inputting all the requested settings, you can review the settings and decide whether to commit them to the DSCP configuration database. System Administration 183 setdscp(8) Privileges OPTIONS EXAMPLES Note - The -y and -n options can be used (with or without the -q option) when running setdscp in interactive mode. You must have platadm or fieldeng privileges to run this command. Refer to setprivileges(8) for more information. The following options are supported: -d domain_id -f -h -i address -m netmask Domain identifier. Must be used with -i address option. domain_id can be 0-23 depending on the system configuration. Forces setdscp to ignore out of range and address conflict errors and commits the new settings. Displays usage statement. When used with other options or operands, an error occurs. Specifies an IP address in the IPv4 dotted decimal format. When used with -m netmask it specifies a network address for all DSCP links in the system. When used with -d domain_id it specifies an individual, domain-specific IP address for use by DSCP. When used with -s, it specifies the IP address used for the Service Processor end of all DSCP links in the system. Specifies a netmask address for all DSCP links in the system. Must be used with -i address. Automatically answers n (no) to all prompts. Suppresses all messages to stdout, including prompts. Must be used with the -i address option. Specifies the Service Processor end of all DSCP links in the system. Displays a detailed message. If this option is specified with the -q option, the -v option is ignored. Automatically answers y (yes) to all prompts. Caution — The IP addresses shown in the following examples are examples only. Refer to the site planning guide for your server for information about valid IP addresses for your network. Using invalid network IP addresses could, under certain circumstances, make your system unbootable! 184 XSCF Reference Manual • Last Revised January 2007 setdscp(8) example 1 Assigning All DSCP Addresses XSCF> setdscp -y -i 10.1.1.0 -m 255.255.255.0 Commit these changes to the database? [y|n] : y example 2 Assigning an Alternative IP address to Domain 1 xscf> setdscp -d 1 -i 10.1.1.26 Commit these changes to the database? [y|n] : y example 3 Specifying a Netmask Address With -q and -y Options XSCF> setdscp -q -y -i 10.1.1.0 -m 255.255.255.0 example 4 Setting DSCP Addresses Using Interactive Mode The default value displayed by each prompt in interactive mode matches the previous configuration. This makes it possible to interactively review and modify DSCP configuration. In this example you only input the network address portion and then press ENTER to accept all subsequent settings. xscf> setdscp DSCP network [0.0.0.0 ] > 10.1.1.0 DSCP netmask [255.0.0.0 ] > 255.255.255.0 XSCF address [10.1.1.1 ] > [ENTER] Domain #00 address [10 1. 1. 2 > [ENTER] Domain #01 address [10 1. 1. 3 > [ENTER] Domain #02 address [10 1. 1. 4 ] > [ENTER] Domain #03 address [10 1. 1. 5 > [ENTER] Domain #04 address [10 1. 1. 6 > [ENTER] Domain #05 address [10 1. 1. 7 > [ENTER] Domain #06 address [10 1. 1. 8 > [ENTER] Domain #07 address [10 1. 1. 9 > [ENTER] Domain #08 address [10 1. 1. 10 ] > [ENTER] Domain #09 address [10 1. 1. 11 ] > [ENTER] Domain #10 address [10 1. 1. 12 ] > [ENTER] Domain #11 address [10 1. 1. 13 ] > [ENTER] Domain #12 address [10 1. 1. 14 ] > [ENTER] Domain #13 address [10 1. 1. 15 ] > [ENTER] Domain #14 address [10 1. 1. 16 ] > [ENTER] Domain #15 address [10 1. 1. 17 ] > [ENTER] Domain #16 address [10 1. 1. 18 ] > [ENTER] Domain #17 address [10 1. 1. 19 ] > [ENTER] Domain #18 address [10 1. 1. 20 ] > [ENTER] Domain #19 address [10 1. 1. 21 ] > [ENTER] Domain #20 address [10 1. 1. 22 ] > [ENTER] Domain #21 address [10 1. 1. 23 ] > [ENTER] Domain #22 address [10 1. 1. 24 ] > [ENTER] Domain #23 address [10 1. 1. 25 ] > [ENTER] Commit these changes to the database * 0- n] £ System Administration 185 setdscp(8) EXIT STATUS SEE ALSO The following exit values are returned: 0 Successful completion. >0 An error occurred. showdscp (8) 186 XSCF Reference Manual • Last Revised January 2007 setdualpowerfeed(8) ...

Herunterladen

Geben Sie zwei Ziffern: