Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
78-3610-09 Cisco IOS Release 11.0 BT Release Note and Update to Configuration Guides and Command References January 15, 1999 This document supplements the Cisco IOS Release 11.0 documentation set with new and changed commands that support Cisco IOS Release 11.0(10)BT and later. Note that Cisco IOS Release 11.0(10)BT is the initial release of Cisco IOS Release 11.0 BT. No prior versions of Cisco IOS Release 11.0 BT exist. The TN3270 server function is supported on a Channel Interface Processor card in a Cisco 7000 series or Cisco 7500 series router. The following Cisco IOS releases are covered by this release note publication: • Cisco IOS 11.0(10)BT • Cisco IOS 11.0(11)BT • Cisco IOS 11.0(12)BT • Cisco IOS 11.0(13a)BT Note Cisco IOS Release 11.0(13)BT was renumbered and released as 11.0(13a)BT.) • Cisco IOS 11.0(14)BT, Cisco IOS 11.0(14a)BT1 Note Shipment of Cisco IOS Release 11.0(14)BT was halted due to CSCdj05366. A fix was implemented and the release was renumbered and released as 11.0(14a)BT1. Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Copyright © 1998 Cisco Systems, Inc. All rights reserved. Introduction • Cisco IOS 11.0(15)BT • Cisco IOS 11.0(16)BT • Cisco IOS 11.0(17)BT • Cisco IOS 11.0(18)BT • Cisco IOS 11.0(19)BT • Cisco IOS 11.0(20)BT • Cisco IOS 11.0(21)BT • Cisco IOS 11.0(22)BT Cisco IOS Release 11.0 BT is based on Cisco IOS Release 11.0. Introduction This Release Note and Update is divided into the following sections: • Release Note, page 2 — Platform Support, page 3 — Cisco IOS Packaging, page 3 — Boot ROM Requirements, page 3 — CIP Boot Image Requirements, page 3 — Memory Requirements, page 3 — Microcode Software, page 4 — New Software Features in 11.0(10)BT, page 4 • Update to Configuration Guide, page 4 • Update to Command Reference, page 19 • Cisco Connection Online, page 57 • Cisco Connection Documentation, page 57 Use this document in conjunction with the Router Products Release Notes for Cisco IOS Release 11.0 and the Cisco IOS Release 11.0 configuration guide and command reference publications, specifically the Router Products Configuration Guide Chapters 1 to 6, Router Products Configuration Guide Chapters 22 to 33, Router Products Command Reference Chapters 1 to 6, Router Products Command Reference Chapters 22 to 33. Release Note Cisco IOS Release 11.0 BT introduces TN3270 server support on Channel Interface Processor (CIP) cards. Note To enable the TN3270 server feature, you must have a CIP card installed in a Cisco 7000 series router or Cisco 7500 series router. The TN3270 server is different from the TN3270 terminal emulation access feature described in the “Configuring TN3270” chapter of the Access and Communication Servers Configuration Guide. Cisco IOS Release 11.0 BT Release Note and Update to Configuration Guides and Command References Release Note Platform Support Cisco IOS Release 11.0 BT supports the following router platforms: • Cisco 7500 series • Cisco 7000 series and Cisco 7000 series with RSP7000 Cisco IOS Packaging The following feature sets are available in Release 11.0 BT. Refer to the Router Products Release Notes for Cisco IOS Release 11.0 for a list of the features provided in the Cisco 7000 and Cisco 7500 series feature sets. • Enterprise (this feature set includes CIP) • Enterprise/CIP2 Boot ROM Requirements Boot ROMs that support Cisco IOS Release 11.0 are required. No special requirements exist for Cisco IOS Release 11.0 BT. CIP Boot Image Requirements The CIP boot image is bundled in the Cisco IOS Release 11.0 BT image. You must have the image that supports your CIP or your CIP2 hardware. You cannot run a CIP and a CIP2 card in the same router. See Table 1 for a list of image names and supported CIP or CIP2 cards. Table 1 11.0 BT Image Names for CIP and CIP2 Hardware Image Names Supported CIP Hardware rsp-k-mz CIP rsp-k2-mz CIP2 gs7-k-mz CIP gs7-k2-mz CIP2 Memory Requirements The memory requirements for Cisco IOS 11.0 BT are shown in Table 2. The CIP supports up to 128 Mb of memory. Table 2 11.0 BT Memory Requirements Cisco 7500 Series and Cisco7000 MinimumRequired Required Main Required CIP Release11.0 with RSP7000 Code Memory Memory Memory Runs From Enterprise Set 8 MB Flash memory 24 Mb 32 Mb RAM (rsp-k-mz) card Enterprise/CIP2 Set 8 MB Flash memory 24 Mb 32 Mb RAM (rsp-k2-mz) card Cisco IOS Release 11.0 BT Release Note and Update to Configuration Guides and Command References Update to Configuration Guide Cisco 7500 Series and Cisco 7000 with RSP7000 Minimum Required Code Memory Required Main Memory Required CIP Memory Release11.0 Runs From Cisco 7000 Series Required Code Memory Required CIP Memory Release11.0 Runs From Enterprise Set (gs7-k-mz) 8 MB Flash memory card 16 Mb 32 Mb RAM Enterprise/CIP2 Set (gs7-k2-mz) 8 MB Flash memory card 16 Mb 32 Mb RAM Microcode Software Note that microcode software images are bundled with the system software image. Bundling eliminates the need to store separate microcod...