Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Information in this document is subject to change without notice and does not represent a commitment on the part of Adaptec or any of its subsidiaries. The software described in this document is furnished under a license agreement. The software may be used only in accordance with the terms of the license agreement. It is against the law to copy the software on any medium. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Adaptec, Inc. TRADEMARKS Adaptec, the Adaptec logo, Snap Server, the Snap Server logo, GuardianOS, SnapOS, and Snap Disk are trademarks or registered trademarks of Adaptec, Inc. in the U.S.A. and other countries. Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their respective companies. REVISIONS Adaptec, Inc. provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Adaptec and its subsidiaries reserve the right to revise this publication and to make changes in the content hereof without the obligation of Adaptec to notify any person of such revision or changes. SANBloc S50 Quick Install Guide The SANbloc S50 JBOD enclosure supports up to 12 Serial Attached SCSI (SAS), 12 Serial ATA (SATA) disk drives, or a combination of SAS and SATA drives (up to 12 drives total). A maximum of seven (7) S50s can be chained to each Snap Server. This Quick Installation Guide describes how to install the SANbloc S50 enclosure and connect it to a 500/600 Series Snap Server. Note To connect the SANbloc S50 enclosure, your Snap Server must be installed with a Serial Attached SCSI (SAS) host adapter. SANBloc S50 Quick Install Guide SANBloc S50 Quick Install Guide 2 Enclosure Features and Accessories 1 Pre-installed disk drives (4 or 12) and pre-installed drive carrier blanks (8 blanks if 4 drives are pre-installed) 8 SAS I/O controller status LEDs 2 Enclosure status LEDs 9 SAS HOST connector 3 Advanced Power and Cooling units (two) 10 SAS EXP connector 4 On/off switch 11 Rackmount kit 5 Power connector 12 Power cables for all regions (6 total) 6 APC unit status LEDs 13 External 4x SAS cable 7 SAS I/O controller 14 Quick Install Guide Quick Install Guide HOST EXP FAULT ! SEP MASTER 1 3 4 5 6 7 8 9 2 11 13 14 12 3 10 Installing Your Adaptec Enclosure into a Rack 1 Ensure that you have these rackmount kit components: • Front rails (1 left, 1 right) • Rear rails, two different lengths (2 left, 2 right) • 20 nuts (10 each of two different types) • 4 small screws and 10 large screws 2 Secure the front rails to the front supports of the rack, using the screws or nuts included in the kit. (Use the nuts if your rack does not have threaded holes.) ) Secure rear rail, using rail length suitable for your rack Rear support Front support Secure front rail 3 Select the right length of rails for your rack, then secure them to the rear supports of the rack, as shown above. Then secure the front rails to the rear rails. Ensure that all the rail connections are tightened and secure. SANBloc S50 Quick Install Guide 4 Remove the plastic covers from the enclosure’s rackmount ears. Caution The enclosure is heavy. To avoid personal injury, have someone help you lift it. 5 Slide the enclosure onto the rails, then push it all the way back until the rackmount ears are flush against the front vertical supports and the enclosure rests completely on the rails. Rackmount ears rest against vertical 6 Secure both rackmount ears to the front vertical supports. Secure to the front vertical supports SANBloc S50 Quick Install Guide Installing Additional Disk Drives If the SANbloc S50 enclosure came with 4 drives installed, you can install up to 8 additional disk drives. The enclosure supports up to 12 SAS or 12 SATA disk drives, or a combination of both (up to 12 drives total). Caution Acclimate new disk drives to room temperature before you install them. Before You Begin While you can combine SAS and SATA drives in the same enclosure; you cannot combine SAS and SATA drives in the same column of drives. If you are combining SAS and SATA disk drives, use the figures below to plan where you will be placing the disk drives. These figures represent enclosures fully-loaded with disk drives. However, the same guidelines apply even if you are filling some of the drive slots with blank drive carriers. Recommended Disk Drive Configurations SAS Disk Drives SATA Disk Drives SANBloc S50 Quick Install Guide Unsupported Disk Drive Combinations Do not include SAS and SATA disk drives in the same column. Do not place a column of SATA disk drives between two columns of SAS disk drives. Installing the Disk Drives 1 Select an open drive slot. 2 Hold the disk drive with the LEDs on the left and the lever fully...