Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
in the United States and other countries worldwide. All other trademarks are the property of their respective owners. Connect serial device Connect Ethernet cable Connect power supply Insert CD Follow wizard Disconnect power supply Disconnect Ethernet cable Re-connect power supply PortServer TS1 W MEI shown What you will need Software & Documentation Software & Documentation If you have a UNIX system and it does not use an auto-mounter, you will need to manually mount the CD. See the back of this guide for UNIX specific instructions. Quick Start Guide Ethernet cable not included PortServer TS W MEI Wireless Series 2 3 1 2 3 RUN WIZARD INSTALL REBOOT Congratulations! Configuration is complete. Go to the User's Guide on the CD for more information. Be sure to check Digi Support for the latest firmware updates at: Applying power with the Ethernet cable connected, will disable wireless access. Applying power with the Ethernet cable disconnected, will enable wireless access. PN:(1P) 90000689 A *If switch 4 is up, termination resistor is connected. If switch 4 is down, termination resistor is not connected. Set serial DIP switch according to your serial device requirements. Pinouts available on back of quick start. Up/On Down/Off EIA-232 EIA-422/485 Full-Duplex EIA-485 Half-Duplex Switch Settings * * 1 4 1 2 3 4 * Power (green) steady blinking; seeking or waiting for an IP address Signal (yellow) RF signal strength indicated by brightness of light Accessing the CD from a UNIX System Software & Documentation Insert CD in system CD drive 1 2 If your system auto mounts the CD, skip to step 5. Auto Mount programs may use the volume information to define a mount point. If the CD volume label is "Digi" then the mount point may be /cdrom/digi UNIX Determine your CD device Common names for CD-ROM devices: NAME EXAMPLE /dev/cdrom /dev/cdrom/dev/cdrom/cdromn /dev/cdrom/cdrom1/dev/cdn/dev/dsk/cktmdn /dev/cd0/dev/c1t2d0 To list descriptions of devices: AIX: lscfgHPUX: - Make sure you have administrator privileges andyour PATH includes /usr/sbinioscan -funC disk Solaris: Most Solaris systems use an auto-mounter. See the man page on vold: man vold 3 Identify the mount-directory. Some common pre-existing mount points: /mnt/cdrom /cdrom Or create your own: mkdir /mnt/mycdrom HPUX - Check to see if pfs is running ps -ef | grep pfs If not, start the daemons: pfs_mountd&; pfsd& Mount the CD by entering one of the commands from the following table: 4 AIX *HPUX SCO UnixWare SCO OpenServer Solaris (Intel & SPARC) Command mount -r -v cdrfs device mount-directory do not use mount, it will not operate correctly pfs_mount device mount-directory See man pages for pfs and pfs_mount for more information. mount -r -F cdfs device mount-directory mount -r -f ISO9660 device mount-directory mount -F hsfs device mount-directory Most systems use an auto-mounter. See the man page on vold: man vold OperatingSystem device is the path to the device file assigned to the cdrom drive, mount-directory is the directory where the Digi CD is mounted Navigate to mounted CD directory, enter: ./setup 5 If you see DISPLAY permission errors when running the CD, you may want to verify your DISPLAY variable is set. To set the DISPLAY variable: DISPLAY=localhost:0.0; export DISPLAYAND/OR xhost +localhost *HPUX When finished, leave the CD directory and pfs_umount cd pfs_umount mount-directory (If you inadvertenly use umount instead of pfs_umount, kill the pfs daemons to remove the CD-ROM.) Linux mount device mount-directory Pinouts Pin 1 RJ-45 Pin EIA-232 EIA-422/485 Full-Duplex EIA-485 Half-Duplex RI TXDTXDDSR RxD-RxD- RTS RTS+ n/a GND GND GND TxD TxD+ TxD+ RxD RxD+ RxD+ SG SG SG CTS CTS+ n/a DTR RTS-n/a DCD CTS-n/a Need help with cabling? Digi TS EIA-232 Cable Adapter Reference Cabling your serial devices to a Digi Product is now simpler than ever with a Digi Cable Adapter. While many custom cabling solutions can leave you with a cable that is either too long or too short for your application, the Digi Cable Adapters are used with commercially available CAT 5 cable of any length. Simply plug standard CAT 5 cable into your Digi Product, connect a Cable Adapter to the other end and plug the adapter into your device. Whether you need a crossover or straight-through connection, or require a DB-9 or DB-25 connector, there is a Digi Cable Adapter solution. For additional cabling information, see the Cabling guide under Documentation on your CD. If you prefer to order cables, see our website at and select Cabling. Part number Adapter Application 76000697 Digi TS DB-9F Console Adapter (4-pack) Bay Accelar, Nortel and other DB-9 DTE devices 76000698 Digi TS DB-25M Console Adapter (4-pack) Sun Sparc, Sun Ultra, terminals, printers and other DTE devices with DB-25 Female ports 76000699 Digi TS DB-25F Console Adapter (4-pack) Cisco, IBM and other DTE devices with DB-25 Male ports 76000700 Digi TS DB-25M Modem Adapter (4-pack) Mode...