Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or more of the following suggestions. 5V power adapter Reorient or relocate the receiving antenna (AAPAC5V) Increase the distance between the equipment and the receiver Connect the equipment to a different power outlet other than the one where receiver is connected Consult a certified television or radio technician Sturdy and heat resistant aluminum enclosure eSATA 3Gbps connection USB2.0 connection RAID selection switch Power connector for Power switch Installation Guide 4. Make sure that the SATA drives are seated correctly on the SATA connectors 1. To remove the front door of the enclosure, loosen screws on each side. of the enclosure. 5. Screw back the front door of the enclosure. 2. Detach the front door of the enclosure. 3. Slide the 2.5’’ SATA hard disk into the drive bay. 6. Tighten the screws (both sides) to secure the front door. How to Configure Raid Raid Setting Table Display RAID Status RAID Selection Switch 4 2 1 0 BIG (span) OFF OFF OFF 1 JBOD (single) OFF OFF ON 2 FAST (strip) OFF ON OFF 3 SAFE (mirror) OFF ON ON 4 SAFE33 ON OFF OFF 5 SAFE50 ON OFF ON 6 RESERVED ON ON OFF 7 GUI ONLY ON ON ON How to Build Raid JBOD a. Setup Raid mode JBOD using RAID selection switch c. Plug the other end of the mini USB data cable & USB power cable to USB ports on your system. Note: Due to the different layouts of Laptops, we suggest to plug the USB cables on opposite sides of the Laptops to avoid weak power from the same side USB ports. Avoid using the front USB ports of desktop because, sometimes, it is too weak to give enough power. eSATA Connection If you are connecting via eSATA, you will have to connect the USB power cable or the 110/220V AC/DC 5V power adapter. Note: To see 2 individual drives (JBOD single) using eSATA connection, the enclosure must be connected to a port multiplier compatible SATA host controller. d. Turn on the power switch. Power Switch e. Press the “RAID Setting” button once. Note: Since the default Raid mode may be different from your new Raid mode setting, it is required to press the “RAID Setting” button once before using Portable Dual Drive RAID enclosure. 1 JBOD (single) OFF OFF ON b. USB Connection Plug in mini USB data cable & USB power cable as shown. USB Data Cable f. Place the cursor on the My Computer icon on your desktop, do a right click and USB Power choose “Manage” by clicking mouse left button Cable i. Place cursor on Disk 1, do a right click then select “Initialize Disk ” g. Select “Disk Management” . j. Press ”OK” h. Disk Management shows the hard disks that are “Unallocated” k. Refer to steps i & j to initialize Disk 2 l. Hard disks will become “Online” o. Choose ”Next” again. m. Place cursor on Unallocated portion and select “New Partition” p. Set up partition size and click “Next” n. Choose ”Next” q. Tick “Quick format” and click ”Next” r. Click ”Finish” u. Format the other hard disk by referring to steps m ~ r. v. When the drive has been formatted, “My Computer” will show two Physical hard disks s. Disk Management shows system is “Formatting” t. When format is finish , it shows the drive as “Healthy” How to build Raid : BIG(Span) Set the DIP switch as above and Refer to Step b ~ v to build the Raid BIG(Span) mode. This time you can see only 1 hard disk only(see following two pictures.) 0 BIG (span) OFF OFF OFF How to build Raid : SAFE50 Set the DIP switch as following and Refer to Step b ~ v to build the Raid SAFE50 mode. This time you can see 2 hard disks ( one is mirror hard disk and the other, BIG. See following two pictures. 5 SAFE50 ON OFF ON To hard disks Two healthy hard disks After Raid SAFE50 is finished, you can see two new hard disks, one is with Raid mirroring and the other is with Raid BIG. Trouble shooting A Can only see “8GB Unallocated” Possible reasons are: A-1 You did not install any hard disk. A-2 During initial installation you forgot to press “RAID Setting” button once. A-3 You have change the Raid mode but forgot to press “RAID Setting” button once. B Show wrong hard disk capacity or wrong hard disk numbers B-1 Normally, it is because you have changed Raid mode setting but did not delete the previous Raid partition. In this case, you will have to delete the previous Raid partition on the hard disks and then, re-organize your hard disks again. C Hard disk LED indicators are blinking with green/red C-1 This is because the Safe (mirror) ...