Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Antec Dateigröße: 200.14 kb Dateiname: NSK4000II_4480II_4480BII_EN_Manual.pdf Unterrichtssprache:

3. Remove the two thumbscrews that fasten the top cover onto the case. These are the only screws you need to remove to open the case. Set these screws aside and keep them separate from the other screws. 4. Slide the top panel toward the rear of the case and lift it up to remove. 5. At the top of each side panel, in front of the power supply, there is a 4”wide tab. Using this, lift and pull the side panels out to remove. 6. Inside the case you should see the power supply, some wiring (LED’s, etc.), an installed I/O panel, a power cord and a plastic bag containing more hardware (screws, brass standoff, plastic stands, etc.). 2.2 Motherboard Installation 1. Lay the case down so that the open side is up. You should be able to see the drive cage and power supply. 2. Make sure you have the appropriate I/O panel for the motherboard. If the panel provided is not suitable for the motherboard, please contact the motherboard manufacturer for the correct I/O panel. 3. Line up the motherboard with the standoff holes. Determine which ones line up and remember where they are. Not all motherboards will match with all of the provided screw holes, and this is not necessary for proper functionality. Some standoffs may be pre-installed for your convenience. 4. Lift up and remove the motherboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the motherboard on the brass standoffs. 7. Screw in the motherboard to the standoffs with the provided Phillips-head screws. 2.3 3.5” Device Installation There is one 3.5” drive cage inside the case. It can hold two external 3.5” drives and three internal 3.5” hard disk drives (HDDs). 1. Remove the screw that fastens the cage to the case. Slide the cage out of the case. 2. Mount your external 3.5” drives into the top two drive bays and internal drives into the other three drive bays that have rubber grommets. Load the drives from the back, lining them up to the front of the drive cage. 3. With one hand supporting the drive, fasten the drive to the cage with the screws provided. 4. Slide and fasten the cage back to the case. 5. Find a small 4-pin connector on the power supply and connect it to the male 4-pin connector on the floppy drive. 3 6. Connect the appropriate connector(s) from the power supply to the hard drive(s). 2.4 5.25” Device Installation There are three external 5.25” drive bays. 1. Looking from the rear of the case you can see metal grills covering the 5.25” drive bays. Carefully push a screwdriver through the metal grill and gently push the plastic drive bay cover outwards until it comes off. 2. Using your hands, twist the metal plate back and forth until it breaks off. Note: Don’t break off the metal grills covering the drive bays that you are not using now. Be careful of the newly exposed metal where the grill was attached, as these areas are likely to be sharp. 3. Fasten the 5.25” device into the drive bay with the screws provided. 4. Repeat the same procedure for other devices. 5. Connect the appropriate connector from the power supply to the device. Connecting the Front I/O Ports 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard manual to ensure that it matches the table below: Motherboard USB Pin Layout 1 2 9 10 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connection) 10 Empty Pin 4 3.2 AC’97/HD Audio Ports There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector linked to the front panel of the case. Pin Assignment for Audio Ports (HDA and AC’97) 10 642 97531 Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L) You can connect either the AC’97 or the HDA connector depending on the model of the motherboard. Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system supports both audio standards, you may only use one connector. 3.3 Switch and LED Connectors Connected to your front panel are LED leads for power and hard disk activity and switch leads for power and reset. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin header locations. Polarity (positive and negative) does not matter for switches. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try reversing the connection. For more information on connecting LEDs to your motherboard, see your motherboard manual. 5 3.4 R...

Herunterladen

Geben Sie zwei Ziffern: