Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Antec Dateigröße: 105.14 kb Dateiname: ec5eb4f4-838d-48f6-8b1b-84911cbaa49b.pdf Unterrichtssprache:

It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come with those components. Sonata Solo / Solo White / Designer 500 / Plus 550 SUPER QUIET MINI TOWER CASES USER’S MANUAL The Sonata Solo / Solo White / Designer 500 / Plus 550 cases are designed with Quiet Computing™ in mind. Many unique design features help make this case quiet and cool. 1. Solid steel structure (1.0 mm thick steel). 2. Two-layer (steel/plastic) side and top panels to deaden noise. 3. Dual hard drive mounting system for maximum noise reduction. 4. Quiet 120mm TriCool™ rear fan. 5. Dual front 92mm fan mounts for spot cooling hard drives. 6. Intake vents along the sides of the front bezel to prevent noise from leaking toward the user. 7. Built-in cable organizer to tuck away extra cables behind the hard drive cage. 8. The Sonata Designer 500 comes with the environmentally friendly EarthWatts 500 power supply unit (PSU), which meets the 80PLUS® specification. 9. The Sonata Plus 550 comes with the NeoPower 550 PSU with better power distribution and modular cabling. 10. The Sonata Solo / Solo White comes without any PSU, which allows you to add the Antec PSU of your choice. Setting Up 1. Place the case upright on a flat, stable surface. 2. Loosen the thumbscrews from the left side panel. Remove it by swinging it out. Note: Do not use your fingernail to pry or lift the panels. 3. Inside the case you should see the PSU, some wiring with marked connectors (USB, PWR etc.), an installed I/O panel, a power cord, a plastic bag containing modular PSU output cables (for Sonata Plus 550 model), a plastic bag with more hardware (screws, brass standoffs, specialty screws, etc.), and six drive rails. 4. Three plastic tabs on the left side of the bezel fasten the front bezel to the metal chassis. Release the tabs from the top down to release the bezel. 5. Swing open the bezel about 45. and gently lift the bezel upward. The front bezel will come off easily. Set the bezel in a safe place. Installing the Motherboard This manual does not cover CPU, RAM, or expansion card installation. Please consult your motherboard manual for specific mounting instructions and troubleshooting. 1 1. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the case isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. 2. Line up your motherboard with the standoff holes, and remember which holes are lined up. Not all motherboards will match with all the provided holes; this is normal, and won’t affect functionality. (In other words, there will likely be extra holes.) 3. Remove your motherboard by lifting it up. 4. Screw the brass standoffs into the threaded holes that line up with your motherboard. Do not over-tighten the standoffs. Some standoffs may be pre-installed for your convenience. 5. Place your motherboard on the brass standoffs. 6. Fasten your motherboard to the standoffs with the provided Philips-head screws. Your motherboard is now installed. Connecting the Front I/O 1. Connect the Reset switch (labeled RESET SW) to the motherboard at the RST connector. Polarity (positive and negative) does not matter for switches. 2. Power Switch (labeled POWER SW) connects to the PWR connector on the motherboard. 3. Connect the Power LED (labeled POWER LED) to your motherboard. For LEDs, colored wires are positive (+). White or black wires are negative (–). If the LED does not light up when the system is powered on, try reversing the connection. For more info on connecting LEDs to your motherboard, see your motherboard manual. 4. Hard Drive LED (labeled HDD LED) connects to the hard drive activity header. Connecting the USB Ports You will find a single 10-pin connector on a cable attached to the front USB ports. This is an Intel® standard connector that is keyed so that it can’t be accidentally reversed when connected to a proper Intel® standard motherboard header. Connect the 10-pin connector to the motherboard headers so that the blocked pin fits over the missing header pin. Note: Please check the motherboard manual for the USB header pin layout and make sure it matches the table below. If it does not match this Intel® standard, please visit Antec’s web store at and search for part number 30095 to order a USB Internal Adapter Cable. This adapter will allow you to connect the front USB to your motherboard on a pin-by-pin basis. Motherboard USB Pin Layout 1 2 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Posit...

Herunterladen

Geben Sie zwei Ziffern: