Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Gigabyte Dateigröße: 7.27 mb Dateiname: Unterrichtssprache:

Required tools: power supply securing screws x 4. cross bar 4-2 Installation of Motherboard The 3D AURORA is compatible with the ATX/Micro ATX/Mini ATX/Flex ATX motherboard. Please confirm the dimension and specifications of the motherboard before installation. Required tool: motherboard standoffs x 9 and securing screws x 9 9 EnglishEnglish 4-2-1 According to motherboard specifications, select proper screw holes, engage the standoffs into the corresponding holes of the casing. 4-2-2 Secure the motherboard with securing screws. Motherboard Code Securing screw Standoffs ATX A1-A9 9 9 MINI ATX M1-M9 9 9 MICRO ATX U1-U9 9 9 FLEX ATX F1-F6 6 6 Select proper “rear I/O panel” of the motherboard (typically supplied by motherboard manufactures). 4-3 Installation of Interface Card The 3D AURORA supports tool-free installation of interface cards, e.g. Graphic card and Network Card, etc. Required tool: None Open the PCI slot retention lock. Remove the internally attached dust-proof PCI cover. Insert the interface card into the expansion slot with care. Make sure all interface cards are fully seated in the corresponding slots. 4-3-1 4-3-2 4-3-3 10 EnglishEnglish 4-4 Installation of Front I/O Panel Incorrect connector installation may possibly burn out the motherboard and other components. Be sure to observe the instructions on installation in the manual. Any loss arising from nonobservance of the proper operation provided is not covered by the warranty. Different motherboards may have different installation positions. For detailed instructions, please refer to the instructions supplied by the motherboard manufacturer. The front panel consists of (1) 2 USB 2.0 / 1 IEEE 1394 / 1 audio line-out jack; and (2) a basic casing power switch control cable kit Required tool: None (1) 2 USB 2.0 / 1 IEEE 1394 / 1 Audio line-out jack 4-4-1 Insert the USB 2.0 connectors into the corresponding sockets on the motherboard. USB 2.0 Connector Pin Definition Pin Definition 1 Power 6 USB Dy+ 2 Power 7 GND 3 USB Dx- 8 GND 4 USB Dy- 9 5 USB Dx+ 10 USB Over Current 4-4-2 Insert the IEEE 1394 connector into the corresponding socket on the motherboard. Please refer to the instructions supplied by the motherboard manufacturer and make sure the correct type of connector prior to installation. a. IEEE1394 Connector A Pin Definition Pin Definition 1 TPA+ 6 TPB- 2 TPA- 7 3 GND 8 +12V 4 GND 9 +12V 5 TPB+ 10 GND b. IEEE1394 Connector B Pin Definition Pin Definition 1 TPA+ 6 TPB- 2 TPA- 7 +12V 3 GND 8 +12V 4 GND 9 5 TPB+ 10 GND c. IEEE1394 Connector C Pin Definition Pin Definition 1 +12V 9 +12V 2 +12V 10 +12V 3 TPA+ 11 TPA1+ 4 TPA- 12 TPA1- 5 GND 13 GND 6 GND 14 7 TPB+ 15 TPB1+ 8 TPB-16 TPB1- 11 EnglishEnglish 4-4-3 Insert the Audio connector into the corresponding socket on the motherboard. Pin Definition Pin Definition 1 MIC 6 Rear Audio (R) 2 GND 7 Reserved 3 REF 8 4 POWER 9 Front Audio (L) 5 Front Audio (R) 10 Rear Audio (L) (2) Basic casing power switch control cable kit. Follow the connectors listed below for installation (see the figure below). Connector Color Speaker Red(+) / Black(-) Reset SW Green(+) / White(-) Power SW Red(+) / White(-) POW LED+ Black POW LED-White H.D.D. LED Brown(+) / White(-) Be sure to remember that different motherboards may have different installation positions. For detailed instructions, please refer to the instructions supplied by the motherboard manufacturer. 4-5 Casing’s Internal Structure The 3D AURORA is equipped with one 12cm silent LED cooling fan at front / two at rear. Required tool: None 4-5-1 Plug the front fan 4-pin power cable into the 4-pin connector on the motherboard. 4-5-2 Plug the rear fan 3-pin power connector into the fan power connector of the motherboard system. 12 EnglishEnglish Installation of 5.25” Front Device Bay The installation of 5.25” CD-ROM is also intended for installation of general 5.25” front device bay. Required tool: None 4-6-1 Open the front panel, remove the 5.25” plastic drive rail and internal metal panel. 4-6-2 Slide the 5.25” CD-ROM into the drive. 4-6-3 Refer to the installation order illustrated in the left figure and secure the 5.25” CD-ROM by controlling the latch (reverse steps for disassembly). 4-6-4 Installation completed. 4-7 The installation of 3.5” floppy disc drive intended for installation of general 3.5” front device bay Required tool: None Installation of 3.5” Front Device Bay 4-7-1 Same as Step 4-6-1. 4-7-2 Slide the 3.5” floppy disc drive into the drive bay. 13 EnglishEnglish 4-7-3 Refer to the installation order illustrated in the left figure and secure the 3.5” floppy disc drive by controlling the latch. (reverse steps for disassembly) 4-7-4 Installation completed. 4-8 Installation of Built-in HDD (Hard Disc Drive) The 3D AURORA provides built-in bays to accommodate up to 5 hard disc drives (after removal of the tool enclosure). The built-in HDD requires securing runners, which can be found in the black tool enclosure. Required tool: Securing runners x 10 i...

Herunterladen

Geben Sie zwei Ziffern: