Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
See your electrician for professional advice. Know your Breville Espresso/Cappuccino Machine Operating your Breville Espresso/Cappuccino Machine Italian designed & made 15 bar pump system 1 and 2 cup filters Advanced crema system Thermoblock heating system Pre-brew function Water level indicator - prevents overflow from drip tray Removable drip tray - catches any coffee spills for easier cleaning Cup warming plate Removable 1.7 litre water tank Auto purge system External water level indicator Froth enhancer - for easier frothing and steaming of milk Stainless steel frothing jug and measuring/tamping spoon included (not shown) Before Using Your Espresso Machine Wash the filter holder and the stainless filters in mild detergent and water. Rinse thoroughly. It is recommended to complete a brewing operation with cold water but without ground coffee before making your first coffee to ensure that all internal piping has been preheated (see ‘Brewing Coffee’ page 8). Filling the water tank • Ensure the Power ‘on/off’ switch is set to the ‘OFF’ position and Selector Control is in the ‘STAND BY’ position. • Switch off at the power outlet and unplug the power cord. • Lift up the water tank lid and remove the water tank. Fill with cold water to the maximum mark and replace back into position in the machine, pressing down firmly so that the water valve opens. Close the water tank lid. The water tank should be filled with fresh cold water before use. Check water level before use and replace the water daily. Do not use mineral or distilled water. Note Preparing the Coffee • Place the 1 or 2 cup filter into the filter holder and fill with ground espresso coffee (use the smaller filter for 1 cup and the larger filter for 2 cups). • Use the measuring/tamping spoon provided to measure 1 level measure of espresso coffee for the 1 cup filter and 2 level measures for the 2 cup filter. It is important to use the correct amount of ground coffee for each filter as the filter perforations have been constructed to utilise the pressure build up in the machine to extract optimal flavour with each brewing. • Distribute the coffee evenly and press down lightly with the tamping end of the measuring spoon (if there is too much coffee, the flow of water can become blocked). Operating your Breville Espresso/Cappuccino Machine continued • Clean any excess coffee from the rim of the filter holder to ensure a proper fit under the brew head. • Place the filter holder underneath the brew head so that the handle is positioned to the left of centre. Lift the filter holder until it contacts the brew head and rotate to the right, as per graphics on the filter holder outlet. Pre-warming cups For optimal coffee temperature, pre-warm the espresso cups by placing them on the cup warming plate. Brewing coffee • Ensure the selector control is in the ‘STAND BY’ position. • Plug the power cord into a 230/240V electrical outlet and switch on. • Press the power ‘on/off’ button to the ‘ON’ position. • The orange ‘heating’ light turns off when the machine has reached the correct temperature. • Ensure the drip tray is in place. • Place one or two pre-heated cups beneath the filter holder outlet. • Turn the selector control to the ‘Espresso’/cup position. • After a few seconds*, aromatic coffee will begin to brew into the cups. A pumping noise will be heard in this operation. *Pre-brew function When the Selector Control is set to the ‘Espresso’/cup position, the 15 bar pump pumps water momentarily, followed by a pause, then continues to pump the water through to the ground coffee in the Filter Holder. This pre-brew function is an advanced feature of the BarVista Espresso/Cappuccino Machine. The ground coffee is moistened by a small amount of water before full extraction. The ground coffee expands and when greater pressure is built up, the brewed coffee is extracted with its full flavour. • When sufficient coffee has flowed into the cups, turn the selector control to the ‘STAND BY’ position. This will stop the flow of coffee. • If the steam function is not required, press the power ‘on/off’ button to the ‘OFF’ position, switch off at the power outlet, unplug the power cord and allow the machine to cool. • Remove the filter holder from the brew head, turn the filter holder upside down to empty the used coffee (used coffee grounds should be thrown away with domestic waste and not down the sink which may block drains). Remove the filter and rinse the filter and filter holder with water and allow to dry. The machine remains ready for brewing and maintains a constant heating temperature whilst the Power ‘on/off’ button remains in the ‘On’ position. If the temperature lowers, the orange ‘heating’ light will illuminate and the coffee machine will automatically reheat to the correct brewing temperature. Note THE METAL PARTS OF THE FILTER HOLDER MIGHT BE VERY HOT. COOL THESE PARTS IN COLD WATER. How to froth milk for a cappuccino or latte The Breville BarVista comes complet...