Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 4.61 mb Dateiname: Unterrichtssprache:

Repeat the operations from step 1 to step 4 twice, then continue with step 6. 6 Remove the pin with the suction tube from the Cappuccinatore. Green 7 Place a container under the Cappuccinatore. ENGLIISH 13 Green 8 Press the “ ” button. The following icon is displayed. Red Green 9 Press the “ ” button to start dispensing hot water. 10 Dispense water until the no water icon appears. 11 At the end, fi ll the water tank again up to the MAX level. Now the machine is ready for brewing coff ee. You will see the display as shown at the left. 12 Place the pin with the suction tube back into the Cappuccinatore. Note: When you haven’t used the machine for 2 or more weeks, the machine will automatically perform an automatic rinse/self-cleaning cycle after you switch it on. Thereafter you need to initiate the manual rinse cycle including brewing a coff ee as described above. The automatic rinse/self-cleaning cycle is also initiated automatically when starting up the machine (with cold boiler), when the machine is preparing to go into stand-by mode or after you have pressed the “ ” button (after a coff ee has been brewed). 14 ENGLISH Measuring and programming water hardness Measuring water hardness is very important for defining the frequency in which the machine has to be descaled and to install the “INTENZA+” water filter (for more detail on the water filter see next chapter). To measure the water hardness follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one measurement. 2 Wait for one minute. 3 Check how many squares have changed the colour to red and then consult the table. 2 3 4 A B C Intenza Aroma SystemMachine water hardness setting 1 Note: The numbers on the water hardness test strip correspond to the water hardness adjustment settings. More precisely: 1 = 1 (very soft water) 2 = 2 (soft water) 3 = 3 (hard water) 4 = 4 (very hard water) The letters correspond to the references that are located at the base of the “INTENZA+” water filter. (see next chapter for this) 4 Now you can program the water hardness setting. Press the “ ” button and scroll the pages by pressing the “ ” button until the following icon is displayed. Yellow Yellow Note: The machine is supplied with standard water hardness setting, suitable for most of the type of water. 5 Press the “ ” button to increase the value or the “ ” button to decrease the value. 6 Press the “ ” button to confirm the setting. ENGLISH 15 15ENGLISHENGLISH15 7 Press the “ ” button to exit the programming MENU. Green “INTENZA+” water filter installation We recommend you to install the “INTENZA+” water filter as this prevents lime scale to build up in your machine and preserves a more intense aroma to your espresso coffee. You can purchase separately the INTENZA+ water filter. Please refer to the maintenance products page in this user manual for further details. Water is a crucial part of every espresso, so it’s most important to always have it professionally filtered. Using the “INTENZA+” water filter will prevent mineral deposits from building up and improve your water quality. 1 Remove the small white filter from the water tank and store it in a dry place. 2 Remove the “INTENZA+” water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and gently press the sides so as to let the air bubbles out. 3 Set the filter according to the measurements performed (see previous chapter) and indicated on the base of the filter: A = Soft water – equals 1 or 2 on the test strip B = Hard water (standard) – equals 3 on the test strip C = Very hard water – equals 4 on the test strip 16 ENGLISH 4 Put the filter into the empty water tank. Press it until it cannot move further down. 5 Fill the water tank with fresh water and reinsert it into the machine. 6 Dispense the entire water tank by using the hot water function (see chapter “Hot water dispensing”). 7 Fill the water tank again. Yellow Yellow 8 Press the “ ” button and scroll the pages by pressing the “ ” button until the following page is displayed. 9 Press the “ ” button to select “ON” and press the “ ” button to confi rm. Green 10 To exit, press the “ ” button. In this way the machine has been programmed to inform the user of the need to replace the “INTENZA+” water fi lter. Replacing the “INTENZA+” water fi lter When the “INTENZA+” water filter needs to be replaced with a new one, the following icon is displayed. 1 Replace the filter as described in the previous chapter. Yellow ENGLISH 17 17ENGLISHENGLISH17 2 Press the “ ” button and scroll the pages by pressing the “ ” button until the following icon is displayed. 3 Select the “RESET” option. Press the “ ” button to confirm. 4 To exit, press the “ ” button The machine is now programmed to manage a new filter. Yellow Note: If the filter is already installed and you want to remove - but not replace -it, select the “OFF” option ins...

Herunterladen

Geben Sie zwei Ziffern: