Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Jura Capresso Dateigröße: 405.76 kb Dateiname: Unterrichtssprache:

READY. • Place a cup under the Cappuccino system (Fig. 18). • Push the Hot Water button (Fig. 4) WATER. 18. • Push the Hot Water button again to stop. READY. During the hot water release you can override the programmed setting by turning the Rotary Dial to the desired volume. 11. VISUAL PROGRAMMING OF BEVERAGE PORTIONS Chapter 14.1 explains how to re-program all parameters (volume, strength, temperature) for all beverage buttons. Re-programming the cup size for coffee and milk can also be done during beverage preparation as follows. READY. • Push and hold the beverage button you want to re-program until display shows ENOUGH COFFEE? or ENOUGH MILK? This way you can make sure your (cappuccino) cup is filled with the desired volume of (milk and) coffee. Example: Visually re-programming the Cappuccino button (Fig. 4). READY. • Prepare the Cappuccino Systems (milk container etc.) to make a cappuccino and place your cappuccino cup under the Cappuccino System (Fig. 16). • Push and hold the Cappuccino button until display shows ENOUGH MILK? • When the desired amount of milk and milk froth is in your cup, push the Cappuccino button again. The display now shows ENOUGH COFFEE? • When enough coffee has been added to your frothed milk push the Cappuccino button again. The display briefly shows OK then READY. The next time you push the Cappuccino button, the C9 OT will produce that amount of milk and coffee. 12. WATER CARE The C9 OT works with: • tap water • bottled water • distilled water. We recommend using tap water or bottled water. Distilled water has no minerals and does not improve the taste of coffee. Water that is heated inside the machine leads to calcium deposits. Tap water has a varying degree of water hardness (chapter 12a). Most bottled water has a low level of water hardness. IMPORTANT: do not use carbonated water or any other liquid in the water tank. You have the following options to take care of the water. • Decalcifying System (chapter 17.1). The machine is factory pre-set to automatically remind you to decalcify. • Clearyl Water Filter Cartridge (chapter 13a). 12a. WATER HARDNESS MONITOR Your C9 OT is set to a water hardness of 10.dH and will automatically indicate when it is time to perform a decalcifying cycle. You can change the water hardness setting from 1. to 30.dH. If you are not sure about the hardness of your water, ask your local water company for the "Water Hardness in Grains." The machine displays the water hardness in the German hardness scale which is a bit different from the American "Grain" scale (see chart below). You can also use the water hardness indicator strip ("Aquadur" in Welcome Pack) to determine the water hardness: • Insert the strip for one second into the water you want to use. Shake off any access water and wait for one minute. One or more sections of the indicator strip will turn reddish. • Change the water hardness setting according to the table below. 19. • Turn the Rotary Dial until the display shows EXIT. Display Equivalent Indicator Strip • Push the Rotary Dial, READY. German American number of Level Degree Grains "reddish" fields The machine automatically reminds you when it is time to decalcify (chapter 17.1). INACTIVE* — — — Please note: You can set the hardness monitor to INACTIVE. In 1. extremely soft water 1-4 1-5 None this case you must use distilled water. In this setting the C9 OT 2. soft water 5-9 6-11 1 to 2 will not remind you to decalcify the machine. 3. medium water 10-14 13-18 2 to 3 4. hard water 15-19 19-24 3 to 4 13. CLEARYL WATER FILTER CARTRIDGE 5. very hard water 20-24 25-30 4 to 5 The machine comes with one Clearyl Water Filter Cartridge. The 6. extremely hard water 25-30 32-38 All 5 Clearyl cartridge • Reduces the water hardness up to 75%. *INACTIVE: You can only use this setting for distilled water. • Removes (if present) up to 85% chlorine, up to 90% lead, up Level 5 and Level 6: If the tap water falls into these two cate to 95% copper and up to 67% aluminum. gories, decalcifying will be frequent. In this case bottled water is • Cleans the water through an upward current principle (Fig. 10) recommended. Most bottled water has a low calcium level. just before the brewing cycle starts, ensuring freshly filtered Please note: If your water has a high calcium content (level 5 or 6) water every time you make coffee. and you use the Clearyl Filter Cartridge we recommend to decalcify • Lasts for 75 liters (~2,500 oz.) of water or up to two months. the machine once or twice a year (chapter 17.2). • Eliminates decalcifying except when using very hard water Please note: If you use Spring or Bottled Water with low calcium (25 grains or higher), see chapter 12. In this case we recomlevels you can set the hardness to 3.dH, "extremely soft water". mended to decalcify the machine once or twice a year. • To reorder cartridges, see chapter 20. 12b. CHANGING THE WATER HARDNESS MONITOR READY. 13a. INSTALLING & ACTIVATING THE CLEARYL CARTRIDGE Example: Change th...

Herunterladen

Geben Sie zwei Ziffern: