Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2. Fill the water tank (if the coffee machine is not to be plumbed in to the mains water supply) and the coffee container (as described below). 3. Turn on the machine at the switch on the top left side of the machine. 4. Push the machine back into the housing. 5. Switch on the machine by pressing 6. Press to dispense a cup of hot water through the steam nozzle. 7. The machine is now ready for use. The water tank It is possible to use the coffee machine without connecting it to the mains water supply. There is an integral water tank which can be used in this instance. To ensure the best results from your coffee, it is recommended that the water tank be emptied frequently and refilled with fresh water, and no water be left in the tank for long periods. When the water tank is empty, the message WATER MISSING will show on the display. To fill the water tank: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Open the lid of the water tank and fill it until the water is 4cm from the top level. Then close the lid. 3. Push the machine back into the housing. Please note: You should only use cold drinking water in this coffee machine, with water hardness level less than 7.F. The water tank can be removed for cleaning, following the steps above, and then lifting it out of the machine. The coffee container You should use only beans for espresso coffee in this machine. Other substances, such as ground coffee, instant coffee, beans treated with caramel, sugar or similar substances should not be used as they can damage the grinder or machine. When the coffee container is empty, the message COFFEE MISSING will show on the display. To fill the coffee container: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Remove the lid of the coffee container and fill it until the coffee beans are 2cm from the top level. Then replace the lid. 3. Push the machine back into the housing. Setting/Adjusting the grind 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Carefully turn the control knob located on the left side of the coffee machine three complete turns either clockwise for a finer grind, or anti-clockwise for a coarser grind. 3. Push the machine back into the housing. 4. Dispense two coffees. COARSE FINE Please note: You must dispense at least two coffees after adjusting the grind before making any further adjustments. The Coffee Machine Press to switch on the coffee machine After a few seconds, GOOD MORNING will show on the display. The machine will heat up, and COFFEE and STEAM will flash on the display. Once the machine is ready for use, COFFEE and STEAM will illuminate constantly, as will the size and number of the coffees last selected (for example 1 SHORT). If COFFEE continues to flash, add coffee beans to the container. If STEAM continues to flash (non-mains plumbed coffee machines only) add water to the water tank. Making espresso coffee 1. Select the coffee size The coffee machine is equipped with three preset coffee size. To select the size required, press to select from the following options: SHORT - 52ml NORMAL - 67ml LONG - 145ml It is possible to adjust the amount of coffee dispensed. To do so follow the steps below. 1. When the coffee is being made, press until the required amount has been dispensed. 2. The display will show MEMO? 3. Press to select the size that is to be set. 4. Press and hold to confirm the setting. The coffee machine will beep. 2. Select the number of coffee cups The coffee machine can prepare one or two cups of coffee simultaneously. To select the number required, press . 3. Make the coffee 1. Place the cup or cups under the dispenser spout. 2. Press to start dispensing. The coffee machine will dispense the selected amount of coffee. To stop the coffee machine dispensing before the end of the preset programme, press again. Dispensing steam 1. Press to select steam and wait for STEAM to stop flashing on the display. 2. Place the cup or container under the steam nozzle. 3. Press and hold to dispense the steam. Release the button when sufficient steam has been dispensed. Please note: Ensure that the spout is placed in a cup or container before pressing , as hot steam can cause scalding. Always use the handle to move the water spout. 5. Make a cappuccino We recommend preparing cappuccinos individually so as to ensure best flavour. 1. Make a medium espresso as described above in a large cup. 2. Press to select steam and wait until STEAM stops flashing. 3. Before putting the container under the steam nozzle, press and hold for approximately five seconds, to flush out any water remaining in the pipes. 4. Fill a 50cl stainless steel container with 10cl milk. 5. Put the steam nozzle into the container so it is at the bottom of the container. 6. Press and hold to steam the milk for a few seconds. Do not heat the milk excessively as th...