Stimmen - 5, Durchschnittliche Bewertung: 4.4 ( )

Hersteller: Sony Dateigröße: 160.51 kb Dateiname: 3860243111.pdf Unterrichtssprache:

Tape deck Amplifier C REC OUT IN LINE OUTIN L R TAPE L R L R c .: Signal flow Setting the voltage selector (only on models supplied with a voltage selector) Check that the voltage selector on the rear panel of the tape deck is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to an AC outlet. TC-WE405 TC-WR661 220V 230– 240V 120V VOLTAGE 220V 240V 120V VOLTAGE Connecting the AC power cord Connect the AC power cord to an AC outlet. Where do I go next? Now you’re ready to use your tape deck. For basic operations, go to pages 5 to 7; for advanced operations, go to the sections starting from page 8. 4 Basic Operations Basic Operations Playing a Tape 24 3 PHONES POWER DECK A DECK B COUNTER RESET PAUSE REC MUTE REC START(DECK B P) SYNCHRO DUBBING A® B HIGH/NORMAL FADER ARL DIRECTION DaRELAY DOLBY NR OFF B C AUTO PrR0) p»a¤ 0) »a¤ REC LEVEL 5 4 3 2 1 0 6 7 8 9 10 p • See page 4 for hookup information. • You can use either deck for playback. z To locate the beginning of a tape and start playback automatically (Auto Play) Press 0 while holding down a. For the reverse side, press )while holding down ». z To play a tape recorded with the Dolby NR* system Set DOLBY NR to the same position that the tape was recorded in—B or C. z What is the Dolby NR system? The Dolby NR (noise reduction) system eliminates tape hiss noise by boosting low-level signals in the high- frequency range during recording, then lowering them during playback. Type C provides greater noise reduction than type B. z You can connect the headphones to PHONES (TC-WE405 only) * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY“ and the double-D symbol aare trademarks of Dolby Laboratories Licensing Corporation. 1 1 Turn on the amplifier and select the tape deck position. 2 2 Press POWER, and then press § and insert a cassette. With the side you want to play facing you 3 Set DIRECTION. To play back Set to One side only A Both sides continuously* a Both decks in succession* RELAY * The deck automatically stops after playing back five times. 4 4 Press a. The deck starts playing. Adjust the volume on the amplifier. To Press Stop playing p Start playback from the reverse side . Pause (deck B only) PAUSE P. Press the button again to resume play. Fast-forward or rewind )or 0when the deck is stopped Take out the cassette ¤after stopping playing 5 Basic Basic Operations Basic Operations Recording on a Tape 2 34 PHONES POWER DECK A DECK B COUNTER RESET PAUSE REC MUTE REC START(DECK B P) SYNCHRO DUBBING A® B HIGH/NORMAL FADER ARL DIRECTION DaRELAY DOLBY NR OFF B C AUTO PrR0) p»a¤ 0) »a¤ REC LEVEL 5 4 3 2 1 0 6 7 8 9 10 p • See page 4 for hookup information. • Use deck B (on your right hand side) for recording. • See "Dubbing a Tape" (page 9) to make a copy of the tape. Note When deck B is recording or in recording pause, all buttons on deck A do not work. 5 1 1 Turn on the amplifier and play the program source you want to record. 2 2 Press POWER, and then press ¤and insert a cassette into deck B. With the side you want to record facing you 3 3 Set DIRECTION. To record on Set to Only one side A Both sides* a * Recording stops when the tape reaches the end of reverse side. 4 4 Press REC r. alights up for recording on the side facing you. If it doesn’t, press aonce. The tape deck automatically adjusts the recording level (see page 8). After the AUTO indicator lights up continuously, stop playing the program source. If you wish to adjust the recording level manually, see “To adjust the recording level manually” on page 7. Basic Operations Basic Operations z To protect recordings Press PAUSE Por a. against accidental erasure 5 Break out the record-protect Recording starts. tab(s) (see page 11). reduced to produce high- quality sound that can be enjoyed even during playback on other tape decks. PHONES PAUSE REC MUTE REC START(DECK B P) SYNCHRO DUBBING A® B HIGH/NORMAL FADER ARL DIRECTION DaRELAY DOLBY NR OFF B C AUTO PrR0) p»a¤ REC LEVEL 54 3 2 1 0 6 7 8 9 10 6 6 Start playing the program source. To Press Stop recording p Start recording from the reverse side »twice in Step 5 Pause PAUSE P. Press the button again to resume recording. Take out the cassette ¤after stopping recording z The Dolby HX PRO* system automatically works during recording (TC-WE405 only) Distortion and noise in the high-frequency response are * HX Pro headroom extension originated by Bang & Olufsen and manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY“, the double-D symbol aand “HX PRO” are trademarks of Dolby Laboratories Licensing Corporation. Use these switches (controls) to perform additional operations DOLBY NR REC LEVEL To record with the Dolby NR system Set DOLBY NR to B or C before you start recording. To adjust the recording level manually After pressing REC rin Step 4 on page 6, turn REC LEVEL so that the peak level ...

Herunterladen

Geben Sie zwei Ziffern: