The kits contain seven louvers plus one louver with two pre-drilled holes (eight total) and these instructions. INSTALLATION INSTRUCTIONS Step 1. Turn off the fireplace and allow it to cool before proceeding. Step 2. Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by rem

Pull forward and lower the panel down to open. Remove the assembly from the fireplace by removing the hinge screw on each end of the assembly. Step 4. Working with one assembly at a time, remove the existing black louvers separating the brackets from the assemblies (see Figure 1). To ease the removal of the brackets, use a side bladed screwdriver and mallet to "tap" down the bend in each bracket finger (restore the bend by hand before reassembly). Replace the black louvers with the brass or bru

Arched Door None 1 ea. Instruction Sheet GENERAL INFORMATION These arch door kits may be used with gas fireplace models listed in Tables 1 & 2. CAUTION INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD! INSTALLATION INSTRUCTIONS Part A: Elite Series Fireplaces Step 1.Slightly lift and pull the existing top radiant panel/hood assembly away from the fireplace, or pull hood and slightly lift and pull the existing louver assembly away from the fireplace. Step 2. Lift and pull the existing top and bott

NO. MODEL WHERE USED 81L34 ADK35CPB EDV3530, ED3530 81L35 ADK40CPB EDV4035, ED4035-2, LMDV-4035, SSDV-4035, MPD4035, EDVST, EDST-2, EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2 81L36 ADK45CPB EDV4540, ED4540-2, MPD4540 81L37 ADK24CPB EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2 98L05 ADK33CPB MDR3328, MDT3328, MPDT3328, MPDR3328, LMDVR-3328 26M43 ADK35CMPB MPD3530, MPD35ST, MPD35PF, MPB35ST, LMDV-3530

NO. MODEL WHERE USED 98L68 ADK35CBS EDV3530, ED3530 98L69 ADK40CBS EDV4035, ED4035-2, LMDV-4035, SSDV-4035, MPD4035, EDVST, EDST-2, EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2 98L70 ADK45CBS EDV4540, ED4540-2, MPD4540 98L71 ADK24CBS EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2 98L62 ADK33CBS MDR3328, MDT3328, MPDT3328, MPDR3328, LMDVT-3328, LMDVR-3328 26M44 ADK35CMBS MPD3530, MPD35ST, MPD35PF, MPB35S

Step 8. Close the bottom radiant panel or louver assembly. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2001 LENNOX HEARTH PRODUCTS P/N 750,021M REV. E 03/2008 1110 West Taft Avenue • Orange, CA 92865

Let the bottom of the door frame swing gently in towards the fireplace ensuring that the gasket seats evenly as the door frame draws shut. Fasten the two latches located underneath the firebox floor to the door’s vee-flange. Close both the latches securely. Step 7. Reinstall the top radiant panel/hood assembly or hood and louver assembly. Make certain that the hood is installed as shown in Figure 3 (clean face models) or Figure 4 (louvered models). The fireplace must not be operated without the

Step 2. Lift and pull the existing top and bottom bustle away from the fireplace. Step 3.Open the bottom compartment door (either a radiant panel or louver assembly) by pushing in simultaneously the left and right top corners of the door (the door is hinged at the bottom). Step 4.Remove the bottom compartment door by sliding the hinge pin, located at the door’s left side, to the right until it disengages from the left corner post hole. Pull the door diagonally to the left, away from the fireplac

Step 8.Center the arch door over the glass frame as shown in Figure 1. Press the arch door onto the glass frame and bend the four corner tabs into the frame’s U-channel as shown in Figure 2. CAT. NO. MODEL WHERE USED 81L34 ADK35CPB EDV3530, ED3530 81L35 ADK40CPB EDV4035, ED4035-2, LMDV-4035, SSDV-4035, MPD4035, EDVST, EDST-2, EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2 81L36 ADK45CPB EDV4540, ED4540-2, MPD4540 81L37 ADK24CPB EDVPF, EDPF-2, EDV

Part B - Merit, Merit Plus & SSDV Series Fireplaces Step 1. Slightly lift and pull the existing top radiant panel/hood assembly away from the fireplace, or pull hood and slightly lift and pull the existing louver assembly away from the fireplace. Step 2. Open the bottom compartment door (either a radiant panel or louver assembly) by pushing in simultaneously the left and right top corners of the door. (The door is hinged at the bottom.) Step 3. Open the two glass door latches located underneath