Stimmen - 4, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Heat & Glo LifeStyle Dateigröße: 2.96 mb Dateiname: Unterrichtssprache:

Design and Installation Considerations Heat & Glo gas inserts are designed for installations into solid fuel masonry or factory built fireplaces that have been installed in accordance with the National, Provincial, State and local building codes. Fireplaces are to be constructed of non-combustible materials and, in the absence of local or regional codes, meet criteria of NFPA 211. No additional outside air source is required. Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits. Prior to installing the gas insert: • Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney. • Replace component parts of the chimney and fireplace as specified by the professionals. • Ensure combustible mantel and surround clearances comply with applicable codes and regulations for solid- fuel fireplaces. In the absence of local or regional codes, refer to NFPA 211. • Ensure all joints are properly engaged and the chimney is properly secured. • Minimum fireplace size. See Section 5.A. • Gas supply piping requirements. • Electrical wiring requirements. • Finishing details. • Whether optional accessories—devices such as a wall switch or remote control—are desired. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified technician, service agency or your dealer. C. Tools and Supplies Needed Before beginning the installation be sure that the following tools and building supplies are available. Tape measure Framing material Pliers Flat blade screwdriver Hammer Phillips screwdriver Gloves Framing square Voltmeter Electric drill and bits (1/4 in.) Plumb line Safety glasses Level Reciprocating saw Manometer Noncorrosive leak check solution 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Caulking material (300.F minimum continuous exposure rating) Stove cement (1200.F or higher continuous exposure rating) D. Inspect Appliance and Components • Carefully remove the appliance and components from the packaging. • The vent system components and decorative doors and fronts may be shipped in separate packages. • If packaged separately, the log set and appliance grate must be installed. • Report to your dealer any parts damaged in shipment, particularly the condition of the glass. • Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry. Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions: • Installation and use of any damaged appliance or vent system component. • Modification of the appliance or vent system. • Installation other than as instructed by Hearth & Home Technologies. • Improper positioning of the gas logs or the glass door. • Installation and/or use of any component part not approved by Hearth & Home Technologies. Any such action may cause a fire hazard. WARNING! Risk of Fire,/Explosion/Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water. Heat & Glo • Grand-I35, Grand-I35-SP, Supreme-I30, Supreme-I30-SP • 2206-900 Rev. K • 6/11 18 Heat & Glo • Grand-I35, Grand-I35-SP, Supreme-I30, Supreme-I30-SP • 2206-900 Rev. K • 6/11 5 Fireplace Size Requirements Figure 5.1 Fireplace Opening In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B). B A G E D C F H I MINIMUM FIREPLACE SIZE Location GRAND-I35 SUPREME-I30 Inches Millimeters Inches Millimeters A Rear Width 23-1/2 597 20-1/4 514 B Front Width 34-5/8 879 30-1/2 775 C Glass Opening Width 31-9/16 802 27-7/16 697 D Glass Opening Height 15-11/16 398 12-13/16 325 E Height-Front 24 610 20-1/2 521 F Height-Rear 21-1/16 535 17-5/8 448 G** Unit Depth 16 406 14-3/4 375 H Venting Depth 10-1/2 267 9-1/2 241 I Height to Top of Glass Frame 22 559 18-1/4 464 * Note: If exhaust collar on insert and fi replace damper do not line up, add 4 inches (102 mm) to minimum fi replace height for bends in vent pipe. A. Minimum Fireplace Opening Minimum fi replace opening requirements for a standard 3/4 inch deep surround are shown in Figure 5.1. For smaller openings, an optional 1-1/2 inch deep surround is available and dimensions are shown...

Herunterladen

Geben Sie zwei Ziffern: