Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
For convenience, if one of the bulbs burns out, it may be a good idea to replace all of the light bulbs. 1. Turn off power to the unit by unplugging the power cord. 2. Let fireplace cool if it has been operating. 3. Remove the two screws on the top corner of screen. Pull the screen upward slightly, and then pull out. 4. Remove the four screws that secure the log set/ember bed in position. 5. Remove log set / ember bed and grate assembly. 6. Examine the bulb(s) to determine which bulbs need to be replaced. 7. While holding the socket, unscrew defective bulb(s) counterclockwise. 8. Install the new light bulb(s) by holding the socket and screwing clockwise. 9. Reinstall the log set/ember bed, grate assembly and screen. Follow the above procedure in reverse order. WARNING: Do not exceed 60 Watts per bulb. The use of higher rated bulbs may result in a fire causing property damage and personal injury. Note: SFE23RE uses three lights bulbs. SFE33RE uses four lights bulbs. 6 ELECTRICAL WIRING DIAGRAM Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing location must be followed. 6 ELECTRICAL WIRING DIAGRAM Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing location must be followed. 7 ELECTRICAL WIRING DIAGRAM Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing location must be followed. SFE33RE 7 ELECTRICAL WIRING DIAGRAM Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing location must be followed. SFE33RE 8 Operating Instructions Heater Front View Remote Control Front Remote Control Back Before programming your transmitter you must first insert two “AAA”batteries. Make sure the main power on/off switch is “ON” position. 1. The ON/OFF button: *Note: When Fireplace is first operated, the default setting will be: brightest flame, and full heating To turn on Heater, press the “ON/OFF”button. To turn off heater,press the “ON/OFF”button again. 2. Flame brightness setting: There are three settings for flame brightness: “1”,“2”and “3 (OFF)”. Press button to decrease the flame brightness, and button to increase the flame brightness. 3. Heating level setting: There are three settings for heating level: “HI”, “LOW”, and “OFF”. Press button to decrease the Heating level and button to increase the Heating level. If set on “HI”, two heating elements will be approximately 90°F; set on “LOW”, the set room temperature will be approximately 70°F. Press “ON/OFF” button to turn on or off the fireplace. Press “HEAT Adjust”button to control heater. Press “FLAME ” button to control the Flame brightness. Manual Operation (without handheld remote) 8 Operating Instructions Heater Front View Remote Control Front Remote Control Back Before programming your transmitter you must first insert two “AAA”batteries. Make sure the main power on/off switch is “ON” position. 1. The ON/OFF button: *Note: When Fireplace is first operated, the default setting will be: brightest flame, and full heating To turn on Heater, press the “ON/OFF”button. To turn off heater,press the “ON/OFF”button again. 2. Flame brightness setting: There are three settings for flame brightness: “1”,“2”and “3 (OFF)”. Press button to decrease the flame brightness, and button to increase the flame brightness. 3. Heating level setting: There are three settings for heating level: “HI”, “LOW”, and “OFF”. Press button to decrease the Heating level and button to increase the Heating level. If set on “HI”, two heating elements will be approximately 90°F; set on “LOW”, the set room temperature will be approximately 70°F. Press “ON/OFF” button to turn on or off the fireplace. Press “HEAT Adjust”button to control heater. Press “FLAME ” button to control the Flame brightness. Manual Operation (without handheld remote) 9 SPECIFICATIONS: Model: SFE23RE series Voltage: 220V/50HZ Total Amps: 6.3A Total Watts: 1380W Heating Ratings: 1200W Dimensions, Cm (H x W X D) Fireplace 96.5x100x39.7 Carton 108x105x440 Weight, Kgs Fireplace 60 Shipping 65 Model: SFE33RE series Voltage: 220V/50HZ Total Amps: 6.3A Total Watts: 1380W Heating Ratings: 1200W Dimensions,Cm (H x W X D) Fireplace 110 x 134 x 43 Carton 114 x 142 x48 Weight, Kgs Fireplace 95 Shipping 104 9 SPECIFICATIONS: Model: SFE23RE series Volta...
Dieses Handbuch ist für folgende Modelle:Kamine - SFE33RE (6.65 mb)