Stimmen - 4, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Satco Products Dateigröße: 1.1 mb Dateiname: Unterrichtssprache:

• The insert front face is tested and approved with this insert and may cover existing air circulation vents or grilles on the solid fuel fireplace it is installed into. Should the face not cover the entire ventilation grille surface, the grille should be left open. • The solid fuel fireplace’s flue damper must be fully locked in the closed position or removed for installation. Note: Decorative trim front faces have been tested and approved to cover existing air circulation vents or grills. • The chimney must be capped. • Install the insert without the front face and make all electrical connections. Note: The warning label above, located in the instruction package, must be affixed to the lower back wall of the existing fireplace prior to installation of the insert. Note: When the front is installed it will cover the gap between the heater and the framing, cabinet, finishing materials or existing fi replace. Heat & Glo • CF230E-B & CF260E-B • 4038-894 Rev C • 11/05 C. Wiring WARNING Shock Risk Improperly grounded outlets could cause electrical shock. • Always use properly grounded, fused and polarized outlets. • Always used ground fault protection where required by electrical code. Note: This heater must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C2.1 as appropriate. All wiring must be done by a qualifi ed electrician. Use appropriate wire to meet local and national codes for rated power consumption. CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. CAUTION Disconnect remote controls during your extended absence. This will prevent accidental operation of the heater. • A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit trips or fuse blows on a regular basis when the heater is operated. Additional appliances on the same circuit may exceed the current rating of the Model Description Voltage Watts Amps (120/208/240) CF230E-B 23 in. fireplace/insert 120 1500 12.5 CF260E-B 26 in. fireplace/insert 120 1500 12.5 circuit breaker. • The heater is wired from the factory with a polarized plug. No provisions have been made for hardwiring. • For ease of electrical hook up, you may wish to install the heater near an existing outlet. A 15 amp, 120 volt circuit is required. • Run the cord out the notch of the front face. • Before plugging the heater into the wall outlet, make sure the control switch is in the “OFF” position. • If the cord does not reach the outlet, a No. 16-AWG minimum wire size extension cord rated for a minimum of 1875 watts may be used. Use minimum length and do not coil cord. • If installing inside a pre-existing fireplace and if permitted by local codes, an electrician may install an outlet box inside the existing fireplace. Place the outlet in the lower back of the firebox. Heat & Glo • CF230E-B & CF260E-B • 4038-894 Rev C • 11/05 FLAMEMOTORTEMPERATUREADJUSTMENTPOTENTIOMETERON_BRIGHTOFFON_DIMSELECTORREMOTETHERMISTORSENSOR110VAC60HZ1300WATTHEATERTHERMALHIGHLIMITBLKREDWHTNCBLKBROWNBLKREDBLK75WATTLAMPSBLUEBLKWHT16GaTHERMOSTATCONTROLMODULEPLUGACMALE1212312123RED2PIN12RED2PIN12ORANGE3PIN123YELLOW4PIN1234DIODEORANGE3PIN123BLKBLKWHTWHTBLKBLKWHT16Ga.35AMPACBLOWERMOTORBLKFigure 4.1 110V/120V Wiring Diagram B R W W NC NO C RW RT Thermistor Sensor Switch Assembly Cable Brown Red Black Black Red White Cable Power Cord Wire with Ribs No Connection Black Wire to Heater Power Cord Black Wire Figure 4.2 110V/120V Wiring Diagram FLAMEMOTORTEMPERATUREADJUSTMENTPOTENTIOMETERON_BRIGHTOFFON_DIMSELECTORREMOTETHERMISTORSENSOR110VAC60HZ1300WATTHEATERTHERMALHIGHLIMITBLKREDWHTNCBLKBROWNBLKREDBLK75WATTLAMPSBLUEBLKWHT16GaTHERMOSTATCONTROLMODULEPLUGACMALE1212312123RED2PIN12RED2PIN12ORANGE3PIN123YELLOW4PIN1234DIODEORANGE3PIN123BLKBLKWHTWHTBLKBLKWHT16Ga.35AMPACBLOWERMOTORBLKFigure 4.1 110V/120V Wiring Diagram B R W W NC NO C RW RT Thermistor Sensor Switch Assembly Cable Brown Red Black Black Red White Cable Power Cord Wire with Ribs No Connection Black Wire to Heater Power Cord Black Wire Figure 4.2 110V/120V Wiring Diagram • Heat & Glo • CF230E-B & CF260E-B • 4038-894 Rev C • 11/05 5 Accessories A. Install the Front Face Install the front face following the instructions packaged with the face. B. Install other Optional Accessories Installation of other optional accessories may be done at this time. The heater is now ready for operation. See Section 7. WARNING Shock Risk Do NOT operate this heater without the front face installed. Heat & Glo • CF230E-B & CF260E-B • 4038-894 Rev C • 11/05 6 Finishing A. Finishing Material C. Mantel • Combustible Material Material which is made of or surfaced with wood, compressed paper, plant fibers, plastics, or any material capable of igniting and ...

Herunterladen

Geben Sie zwei Ziffern: