Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
*Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, NY 10036. Page 4 CHG/CHR Figure 2 CLEARANCES Minimum Clearances From Combustible Construction (Figures 2 and 3) Side 6" Rear 6" Top 47" from top of unit or 96" from floor Floor Combustible Minimum Clearances From Combustible Construction with 20 lb. Propane (LP) Tank Attached to Outdoor Gas Fireplace (Figure 4) Side 6" Side, Corner Installation 7" Top 47" from top of unit or 96" from floor Floor Combustible Warning: When selecting a location for your outdoor chimenea, it is important to consider that any ceiling, overhang or other surface located above the chimenea can discolor due to heat or carbon particles generated while unit is operating. Attention: Rain cap must be placed on outdoor chimenea when not in use. Rain cap will prevent rain from entering top of chimenea. Without rain cap in place, rain can wash soot off logs on burner. Soot from logs will stain your patio or deck. Figure 3 Figure 4 CHG/CHR Page 5 SET-UP INSTRUCTIONS 1. Remove packing material from top of box. 2. Lift chimney section out and set aside. 3. Remove remaining items and packing from inside outdoor gas fireplace firebox. 4. Lift firebox out of box and sit on flat surface near desired final location. Leave adequate room around outdoor gas fireplace to work. Locking ring for chimney should be facing down. Figure 5 5. Remove washers and nuts from three legs. Install the three legs using the bolts, washers and nuts provided. Reach through the opening in the outdoor gas fireplace to tighten the leg bolts securely. Figure 5 6. Invert the outdoor gas fireplace firebox to sit on its legs. 7. Remove the 4 5/8" bolt and 5/16 nut that are holding the burner in place. Carefully remove the burner from the firebox. Remove the 2 screws and nuts that are holding the hold down bar in place. Remove the packing materials from the burner. Unpack the cast iron logs and set aside. Figures 6 and 7 8. Holding the burner assembly securely with two hands, tip the burner to a position where it will fit through the front door opening. The gas inlet plumbing, control panel and regulator hose assembly should be pointing to the left and somewhat down as you maneuver the burner through the door. Guide the regulator hose and control panel through the large hole in the bottom of the outdoor gas fireplace. The burner should come to rest on the three flat tabs that protrude from the firebox wall and the control panel should be approximately centered between the left front leg and the rear leg. The burner should be repositioned if needed so that there is an equal gap of approximately 1/2" between the outer curved perimeter of the burner and inner firebox wall. The flat edge on the rear of the burner should be parallel with an imaginary line connecting the front legs. Figure 6 Figure 7 Figure 8 9. The installation sequence is to interlock the flicker shield halves first to prebend the tabs. Place the left half under the outdoor gas fireplace with the cut-out around the pipe. Interlock the right half with the left half. Page 6 CHG/CHR Figure 8 10. Place the hold-down bar under the flicker shield. Push the flicker shield and hold-down bar up to the bottom of the outdoor gas fireplace. Figure 9 11. Insert the 4 5/8" hold down bolt through the hole in hold down bar and flicker shield and rear burner cross support. Secure with 5/16" nut from inside of firebox. Figure 9 12. Move the outdoor gas fireplace to its permanent location. Follow installation instructions to determine the proper distances to adjacent combustible materials. Adequate room must be left behind the outdoor gas fireplace for the LP tank and to the left side for access to the control panel. Figure 10 13. Install the three cast iron logs. Install the diagonal center bottom (#1) log first. Holes in (#1) log are to be positioned closer to front of burner assembly. Add the left cross (#3) log and then the right cross (#2) log. Recesses, tabs and holes are provided to locate the logs properly. See Figure 10 for proper placement. Installation of logs is completed. Figure 10 Refer to the following warning. Warning: Failure to position the parts in accordance with this photograph or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. Figure 11 14. Attach the 20 lb. LP tank support hook to the hole located in the rear center of the outdoor gas fireplace firebox wall. This hole is approximately 18" from the floor. Use the bolt, washer and nut provided and tighten by reaching into the firebox. Figure 11 15. Set the LP tank in place. The gas outlet fitting on the tank should be facing toward the left when viewed from the front. The alternate is to face the outlet connection toward the rear. Lift the tank slightly and hook onto the tank support hook. One of the holes in the tank handle will fit over the hook. 16. Connect the QCC-1 fitting on the regulator hose to...
Dieses Handbuch ist für folgende Modelle:Kamine - CHG (162.32 kb)