Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
The safety alert symbol, is a universally recognized symbol used to identify safety information about hazards that can result in personal injury. When this symbol is used you should pay very close attention to what is written. Review these instructions before beginning assembly or using your fireplace. Assembly 1. Carefully unpack all parts from shipping box. NOTE: In Steps 2 and 3, the stand is assembled up side down for ease of assembly. Use a ground cloth to protect the finish. 2. Align holes in Leg Assembly Brackets with holes in Top Ring. Attach with two small screws per leg. Hand tighten. FOLLOW INSTRUCTIONS AND WARNINGS TO AVOID FIRE, SERIOUS INJURY OR DEATH. WARNING • Outdoor use only. Never use in enclosed area. Use in unventilated areas will endanger your life. • Keep away from all combustible materials including gasoline and other flammable liquids and vapors. • Use on a level, noncombustible surface only. Keep away from house, garage, balconies, or eave overhangs. • Keep out of the reach of children. • Be sure screen is in place while in use and do not use in windy conditions. • Do not overfill firebowl or use to burn leaves and trash. • Exercise the same care you would with an open fire. • Never leave unit unattended when hot or in use. • Completely extinguish fire before leaving. • Use gloves when handling or moving. Ashes can remain warm for a long time after extinguishing. • Dispose of cold ashes properly. • Do not modify in any way nor use with parts not expressly approved by Coleman. • Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Contact local authorities regarding possible burn restrictions before using product. Fireplace Parts Check List • Check package for all parts needed for assembly. ¦ 1. Firebowl ¦ 7. Leg Support Ring ¦ 2. 4 Pc. Screen Assembly ¦ 8. Screen Support Rings (2) ¦ 3. Handle ¦ 9. Hardware Kit ¦ 4. Dome Lid ¦ 10. Leg Assemblies ¦ 5. Protective Cover ¦ 11. Grates ¦ 6. Top Ring • Check all items for shipping damage. Call Coleman at 1-800-835-3278 or TDD: 316-832-8707 if you have any problems. 1 2 4 5 6 79 10 11 8 3 Assembly (cont.) 3a. Assemble Leg Support Ring to the four leg assemblies. Fasten to Leg Brackets with one small screw per leg (see arrows). Tighten all fasteners. 3b. Install four foot pads, one into each leg. NOTE: In some models, the foot pads are pre-installed by the factory. 4a. To assemble screen, align holes in the 3 screen panels with the holes on outside edge of screen support ring. Attach with small screws and hex nuts but do not tighten at this time. NOTE: Make sure latch bracket panel and hinge panel are positioned as shown for proper installation. Latch Bracket pointing up Hinge Panel To p Ring (Large) Assembly (cont.) 4b. Align holes in the 3 screen panels with the holes on outside edge of the remaining screen support ring. Attach with small screws and hex nuts. Tighten all screws and hex nuts on the screen assembly at this time. 4c. Install screen door by inserting pins into hinge slots on the screen hinge panel 5. Turn frame right side up. Place Screen Assembly into frame. Make sure door is centered between two Leg Assemblies, and can open and close properly. 6a. Assemble screen door latch. NOTE: Two hex nuts and latch bar will assemble on the inside of the screen door. 6b. Insert handle from outside. Loosely assembly one hex nut. The handle should freely turn. Point the handle downward to begin the next step. { (See Note) HandleLatch Bar 6c. Slip latch bar onto handle threads. Align “D” slot in latch bar with flat on handle threads. The latch bar should point toward the left. Assemble the second hex nut to finish the assembly. This hex nut functions as a “jam nut”, and will tighten against the first hex nut assembled in Step 5b. 6d. Tighten the “jam nut” with a wrench. 6e. Proper installation of the latch assembly. 7. Install the firebowl. NOTE: An inch or two of sand should be used in firebowl beneath the grate. 8. Install two grates. Assembly (cont.) 9. Attach handle to lid using 2 screws and hex nuts. Tighten fasteners. Set Up and Use WARNING Never leave unit unattended when hot or in use. Keep out of reach of children. For outdoor use only. Never use in enclosed area. Use in unventilated areas will endanger your life. 1. Place unit on a level, noncombustible surface. Keep well away from house, garage, balconies or eave overhangs. Do not use on wooden decks. 2. Be sure grate is placed in firebowl. Add newspaper, kindling & wood on top of grate. 3. Ignite newspaper & kindling with match or butane lighter. 4. Once fire is lit, close and latch the screen door. 5. Screen door handle is hot when in use. Take care when opening and closing the screen door. After Use WARNING To avoid burns – use heavy gloves when handling hot surfaces. 1. Completely extinguish fire before leaving. 2. Do not use water to douse the fire as this may wa...