Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If continuity is not indicated, switch(s) is defective and must be replaced. Note: Before replacing “OFF/ON” switch, be sure to check wiring for loose connections or broken wires and repair as needed. 2. Burners come “ON” but go “OFF.” A. Burner orifice plugged. Check main burner orifice(s) for stoppage. Clean or replace. B. Obstructed vent system. Check vent system for obstructions. START CHECK • Turn Off Gas Supply • Assure Valve Switch Is In ON Position • Disconnect Control Harness • Set Thermostat To Call For Heat • Plug Control Harness Into Valve. Wait For Internal Check Delay. • Igniter Warms Up And Glows Red. NO • Replace Igniter/Flame Rod Assembly. YES YES1 • With Pilot Burner Cable Connected, Measure NO Voltage At Valve HSI Element Output. 24V Nominal. (See Insert B) 1 2 YES • Replace Valve. Insert A End View Of Control Harness Connector 24 Volt Hot 24 Volt Common 24 Volt Switched Check For Damaged Or Missing Terminals In Connector Igniter Terminals Insert B • Turn On Gas Supply. • Pilot Burner Lights. NO NO • Check That Pilot Gas Is Flowing. Wait To • Replace Valve. Assure Plot Gas Tubing Is Purged. Recycle Call For Heat If Necessary. YES NO • Measure Voltage Between 24V Hot And 24V Common Leads To Valve Control. Must Measure At Least 19.5 VAC With Igniter Powered (See Insert A). To Identify Proper Lead, This Check Must Be Done With The Valve Control Connected And Igniter Powered. • Replace Pilot Assembly. • Check Transformer And Line Volt Supply. YES YES • Main Valve Opens And Main Burner Lights. • Check That Pilot Flame Makes Good Contact With Pilot Burner Flame Rod. NO • Check For Good Electrical Connection Through The Pilot Tubing. • If Both Of The Above Are Good, Replace Igniter/Flame Rod Assembly. YES YES • Check For Proper Voltage At Control Harness (See Insert A). Voltage Should Be 24VNO Between Thermostat Or Pressure Switch And 24V Common And 24V Hot. 2 YES • Line Voltage Power • Low Voltage Transformer • Limit Controller • Thermostat • Wiring • System Is Okay. • Cycle Thermostat Off And Back On. • Main Burner Lights. NO • Replace Valve. 1 Igniter Will Cycle Off And Back On Once During The 90 Second Ignition Trial. All Voltage Measurements Must Be Taken While The Igniter When Measured Voltage At Connections, Use Care To Assure Terminals Are Not Damaged. Is Powered. 2 ACCESSORY COMPONENTS ACCESSORY COMPONENTS Remote Control System (Standard) H0249 RCL Standard Remote Control System (Model RCL) The Model RCL (Standard) Remote Control System, features a simplistic on/off control function for the fireplace. This model includes a hand-held transmitter, a remote receiver with wall-mount coverplate and all hardware required to install the unit. The remote receiver can be wall or hearth mounted. The transmitter has ON and OFF functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed, a signal light illuminates briefly to verify that a signal has been sent. The Model RCL is designed to operate with all millivolt ignition systems, as well as electronic ignition systems. It may be installed with use for either natural or propane gas appliances. The RCL offers ease of installation and allows you to execute on-off commands to the fireplace effortlessly with one simple motion. The Model RCL comes complete with detailed operating instructions. Pine Cones and Wood Bits 91L05 FPCK Twelve Piece Ember Kit A twelve piece ember kit (model FPCK) has been developed to provide a means of enhancing the already impressive log presentation of this fireplace. This kit contains three (3) ceramic fiber pine cones and nine (9) ceramic fiber debris wood bits. All twelve elements will not be consumed in the flames and may be placed within the presentation area (without impinging any of the lofting flames) to add realism and enhance the rustic look and appeal of the fire. Decorative Volcanic Stone 80L42 FDVS Bag of Glowing Embers 88L53 FGE Decorative Volcanic Stone The decorative volcanic stone, Model FDVS, can be used to enhance the look of your appliance. Spread the decorative volcanic stone evenly around the bottom of the firebox. Bag of Glowing Embers Replacement ember materials are available for use with these appliances. Order a bag of Glowing Embers, Model FGE to replace ember materials as part of the periodic maintenance of the appliance. Bi-Fold Doors 12M20 12M21 12M22 12M2312M24 12M25 38LBF 38LBF-BB 38LBF-BS 43LBF 43LBF-BB 43LBF-BS Bi-Fold Doors Your appliance can be fitted with beautiful bifold doors. Model 38/43LBF doors are available for use with these appliances. Doors are easily fitted to the fireplace opening. Model 38/43LBF doors come with standard black finish. Model 38/43LBF-BB doors have a beautiful bright brass finish. Model 38/43LBF-BS doors are made of brushed stainless steel. To ensure warranty and to prevent a potential fire hazard, do not use any other doors on these appliances. Touch-Up Paint Kit 90L73 FTPK-B Touch-Up Paint...