Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Vermont Casting
Dateigröße: 967.78 kb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
10 Correct door position during operation. Pilot Thermodisk On/Off Switch Valve HV105 Fig. 9 Remote switch wiring. TPTHTHTP ODGSR Series Outdoor Gas Fireplace Operating Instructions Log Installation 1. Remove logs from the packaging. As with all plastic, these bags are not toys and should always be kept away from children and infants. 2. Place left rear log on rear log support. Ensure that log is firmly positioned and there is no side-to-side movement. (Figs. 11 & 12) 3. Carefully place Ember Log between grate and burner. (Figs. 11 & 12) 4. Place the front of right rear log on the burner and the back of the log on the rear log support. 5. Place the top logs onto the locator notches. Ensure the logs are secure. (Fig. 11 & 12) Right Cross Log Left Cross Log Left Rear Log Right Rear Log Ember Log LG317 Fig. 11 ODGSR36 log placement. Left Cross LG318 20007114Left Rear Log Log Middle Cross Log Right Cross Log Right Rear Log Log Left Ember Grate Fig. 12 ODGSR42A log placement. Log Right Ember First Firing Upon completing the gas line connection, a small amount of air will be trapped in the line. When first lighting the unit with pilot light, it will take a few minutes to purge the trapped air. Once purging is complete, the pilot and burner will light and operate as indicated in the instruction manual. Subsequent lightings of the appliance will not require purging. When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to paint and lubricants used in the manufacturing process. After each lighting, vapor may condense and fog the glass; this moisture disappears in a few minutes of burning. ODGSR Series Outdoor Gas Fireplace Flame Adjustment For units equipped with Hi/Lo valves, flame adjustment is accomplished by rotating the Hi/Lo adjustment knob located near the center of the gas control. Turn Turn clockwise counterclockwise to lower to increase flame height flame height Fig. 16 Proper pilot flame height. FP581 3/8"-1/2" NOVA SIT Pilot Fig. 13 Flame adjustment knob for SIT820 valve. Flame Characteristics It is important to periodically perform a visual check of the pilot and the burner flames. Compare them to the illustrations below (Figs. 14, 15, 16). If any of the flames appear abnormal call a service person. Red Glow LG319 Fig. 14 ODGSR36A flame appearance. LG320 Fig. 15 ODGSR42A flame appearance. 10 20007114 ODGSR Series Outdoor Gas Fireplace Optional Weather Enclosure Optional Stainless Steel Hood An optional weather enclosure is available to protect the burner when not in use. CAUTION: Do not use the weather enclosure if the unit has glass doors installed. Installation Instructions 1. Turn the unit OFF and allow to cool. 2. Grab the weather enclosure by the handle(s). 3. Slide the top of the weather enclosure up between the back of the surround top and the screen rail. (Fig. 17) 4. Push the bottom of the weather enclosure into the firebox just enough to clear the valve access cover and set down. (Fig. 18) Surround Top Weather Enclosure Screen Rail KT457 Fig. 17 Place top of weather enclosure between surround top and screen rail. Screen Hearth Brick Valve Access Cover KT458 Fig. 18 Push bottom of weather enclosure into firebox. An optional stainless steel hood is available for both the ODGSR36A and ODGSR42A. NOTE: The stainless steel hood may NOT be used when the optional glass doors are installed. Installation Instructions: 1. Turn the unit off and allow to cool. 2. Place the hood so the 2..." (67 mm) slot clears the sensor plate located under the fireplace opening on the top left side. (Fig. 19) 3. Secure the hood to the unit using the three (3) slots in the hood and the pilot holes in the unit with the stainless steel sheet metal screws provided. (Fig. 19) 4. Align the sides of the hood so the pilot holes on the right and left sides of the unit are exposed through the slots on the ends of the hood. Secure using the remaining stainless steel sheet metal screws. (Fig. 19) Stainless Steel Hood Stainless Steel Sheet Metal Screws (5) Sensor Plate Slot FP1635 Fig. 19 Secure stainless steel hood with five (5) sheet metal screws. ........... ................... ODGSR Series Outdoor Gas Fireplace Lighting and Operating Instructions FOR YOUR SAFETY READ BEFORE LIGHTING • If you cannot reach your gas supplier, call the Fire Department C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Applying force or any attempted repair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water. A. This heater has a pilot which must be lit manually. When lighting the pilot follow these instructions exactly. B. BEFORE LIGHTING smell all around the heater a...
Dieses Handbuch ist für folgende Modelle:Kamine - ODGSR36A (967.78 kb)