Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
If the venting system is disassembled for any reason, a qualified service technician should follow vent installation instructions for proper reassembly and proper sealing of the venting system components. However, more frequent periodic inspections and cleanings should be performed by the homeowner. Clean Lower Control Compartment Keep lower control compartment clean by vacuuming or brushing it out at least twice a year (also clean the air venturi with a brush or wire). More frequent cleaning may be required due to accumulation of lint from carpeting, bedding materials, pet hair, spider webs, etc. It is very important that control compartments, burners, circulating air passageways and air venturi on the appliance are NOT obstructed in any way. Cleaning Glass (see Front Glass Enclosure Panel, Removal and Installation on Page 9 ) Note: Clean glass after first two weeks of operation (after Burn-In period is over) and then only when necessary and when the fireplace is cool. Wipe surface with clean, dampened, soft cloth. Follow with dry, soft towel as desired. Take care not to scratch the glass surface. The viewing glass should be cleaned periodically to remove any build-up caused from the following: IMPORTANT Do not use abrasive cleaners on glass. Never clean glass when hot. • During start-up, it is normal for condensation to form on the inside of the glass (this condensation and fog will usually disappear in a few minutes). The moisture can cause lint, dust and other airborne particles to cling to the glass surface. • Initial curing of the high temperature paint and burning off of lubricants used in the manufacturing process may result in a film on the glass. • A white coating may form on the glass as a result of impurities and minerals in the fuel. It is recommended that the glass be cleaned two or three times during each heating season, depending on the circumstances present. The following cleaning solutions are approved for use to clean glass: • Non-ammonia based household cleaner • 50%-50% mix of white vinegar & water • gas fi replace/stove glass cleaner Inspect Glass Gasket -Visually inspect the gasket on the backside of the glass enclosure panels. The gasket surface must be clean, free of irregularities and seated fi rmly. Cleaning Logs And Burner Cleaning Logs And Burner dling the fiber logs, as they become quite fragile after curing). Vacuum out any foreign matter (lint, carbon, etc.) on the burner. Ensure the burner ports are “open.” Remove any carbon deposits from the under side of the logs using a vacuum cleaner, or a soft bristled brush (i.e. paint brush). Note: Improper positioning of logs can create carbon build-up and will alter the performance of the appliance. Replacing Logs - If the logs become damaged by accident or improper handling and need replacement, use only the proper replacement logs from manufacturer (see Page 23 for ordering information). Re-Install Embers, Logs and Vermiculite -Carefully follow placement instructions on Pages 9 to 12 ). All logs should fit onto corresponding pins and/or log stoppers. This will ensure a proper fl ame and safe combustion. Inspect Wiring Refer to wiring diagrams on Page 14. WARNING Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Inspect and clean all wire connections. Ensure that there is no melting or damage. Inspection should include: • Terminals at the Valve • OFF/ON Switch • (Optional Control Switch) Remote Control or Remote Wall Switch Kit Inspect Burner Flame Appearance Ensure that the burner flame appearance resembles the flame shown in Figure 15 and as described in Flame Appearance and Sooting on Page 13. The Homeowner must contact a qualified service technician at once if any abnormal condition is observed. Small Area Paint Touch-up The finish of the appliance is a high quality powdercoat. Only use factory supplied powdercoat paint kit for touch-ups. Paint is available at your local authorized Lennox Hearth Products dealer (cat. no. 90L74). Never attempt to paint a hot fi replace. Do not attempt to repaint the appliance until the finish is completely cured (see Burn-In Period on Page 3 ). If the surface later becomes stained or marred, it may be lightly sanded and touched up with spray paint. Front Glass Enclosure Panel WARNING Do not attempt to touch the front enclosure glass with your hands while the fi replace is in use. WARNING Do not operate appliance with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualifi ed service technician. WARNING Handle this glass with extreme care! Tempered glass is susceptible to damage – do not scratch or handle roughly while reinstalling the glass door frame. WARNING Do not attempt to substitute the materials used on this door, or replace cracked or broken glass with any materials other than those provided by the appliance manufacturer. WA...
Dieses Handbuch ist für folgende Modelle:Kamine - MPB35ST-NM (1.55 mb)
Kamine - MPB35ST-NM (1.55 mb)