Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not connect 110-120 VAC to the gas control valve or the on/off circuit on this fireplace. IMPORTANT INSTALLATION NOTE FOR MODELS USING THE FIREBACKS: Follow the steps below if installing the firebacks with an accent light. • Remove the burner. • Install the rear fireback. • Install the accent light. • Replace the burner. • Install the side firebacks. 1 Remove the burner (see the manual for details). 2 Install the accent light and remove the cover plate as shown below. AAAAAA screw. AAAAAAAAAAAA a b NOTE: On the DVS, make sure to use the lower screw. NOTE: To prevent heat-damage to the wires, make sure this clip holds the wires down, away from the burner. 3 Attach the wire plate as shown below. AAAAAAAAAAAAAAAAAAAAAAAAAAAA Wire Plate a b Remove this screw, position the accent light assembly in the same location, and attach with the same Remove this cover plate and gasket. NOTE: The cover plate is here on the DVS. NOTE: Once the light is in place, remove the protective covering. Do not touch the halogen bulb - this may lead to premature bulb failure. Route the wires from the accent light through the gasket and firebox floor. Use the screws removed in step “2” to attach the wire plate to the firebox floor (make sure the gasket is properly aligned). Once the wire plate is in place, pull the excess wire through the grommet, towards the front of the insert. © Travis Industries 4060111 100-01174 42 Optional Equipment (for qualified installers only) 42 Optional Equipment (for qualified installers only) 4 Attach the rheostat assembly and wiring harness as shown below. Attach the quick- connect from the accent light to the quick-connect on the rheostat wiring accent light. AAAAAAAA Disconnect the molex connector leading to the power cord. Attach the two molex connectors on theSlide the rheostat assembly into rheostat wiring harness to the power cord and the molex connector on the appliance. harness. Use the included wire nut to connect the wire leading from the rheostat to the remaining wire leading from the included nuts. place and secure with the a d e b c NOTE: Make sure the grounding wire remains attached (if applicable). Make sure all wiring does not contact the firebox or blower (use wireties if necessary). 5 Restore the firebox to the correct configuration (replace the burners, etc.). OFF LOW HIGH Turn the dial all the Turn the dial 180° The high position way counter-clockwise clockwise until the light is all the way until it clicks off. begins to glow. clockwise. Accent Light Operation NOTE: The accent light responds best when turned to high, then turned down to the desired light level. © Travis Industries 4060111 100-01174 Optional Equipment (for qualified installers only) 43 Optional Equipment (for qualified installers only) 43 Lower Surround Panel The older lower surround panel (sku 98500619 and 98500628) are installed in a different fashion than illustrated in the instruction sheet included with the panel. Follow the directions below. 1 Prepare the panel following the directions below. Use the larger DVL Insert Bracket Lower Panel Top Clip Use tape to secure the clips to the bracket (you may also wedge the clips into place). This holds the clips in place Discard the bottom clips Discard the smaller DVS Insert Bracket Secure the lower panel to the bracket with the nuts (included with the panel). during installation. 2 Attach the panel to the insert following the directions below. Attach the lower surround panel to the inset with the nuts (included with the panel). © Travis Industries 4060111 100-01174 44 Index 44 Index Additional Items Required....................................7 Adjusting the Blower Speed ..................................29 Adjusting the Flame Height..................................28 Air Shutter Adjustment ........................................24 Altitude Considerations........................................13 Before You Begin ...............................................26 Blower Operation.................................................29 Cap (Termination) Requirements...........................13 Clearances........................................................10 Condensation on Glass (see "Starting Heater") .......28 Controls............................................................26 Dimensions .......................................................6 Electrical Connection ..........................................19 Face Sizing........................................................11 Factory-Built (Metal) Wood-Burning Fireplace Requirements ....................................................9 Fan Operation....................................................29 Features ...........................................................6 Firebacks ..........................................................39 Fireplace Requirements.......................................8 Flame Height.....................................................28 Gas Inlet Pressure..........................