Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Consult your installer or dealer for details. • Do not place any combustible items on top of or directly in front of the fireplace, even temporarily. The optional thermostat may start the fireplace causing a combustible item to ignite. • If the fireplace turns on and off frequently while using the thermostat, you may want to adjust the flame height down until it produces just enough heat needed. Adjusting the Flame Height OFF ON • Your fireplace has an adjustable flame to tailor the look and heat output to your specific needs. It is adjusted by turning the middle dial on the gas control valve. Index Mark Flame Height Adjustment Knob Turn counter-clockwise to adjust the flame higher, clockwise to lower. © Travis Industries 4071130 100-01196_000 Operation 9 Operation 9 Adjusting the Optional Blower Speed The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to temperature (approximately 10 minutes after starting). See the illustration below for instructions on adjusting the blower speed. OFF HIGH LOW Turn the dial all the way counter-clockwise The high position is all the way counter-clockwise, Turn the dial all the way clockwise. until it clicks off. without clicking off. Normal Operating Sounds Blower Snap Disk This part can produce a clicking sound as it turns the blower on and off. Gas Control Valve As the gas control valve is turned on and off you will hear a dull clicking sound. This is the valve opening up and shutting down. Normal Operating Odors The appliance may creak with change of temperature -- THIS IS NORMAL. Extinction Pops It is not unusual, especially on Propane (LP) appliances, to experience a "pop" when the burner is shut off. Pilot Flame The pilot flame, which remains on, makes a very slight "whisper" sound. Blowers This heater has optional blowers to push heated air into the room. You will hear the sound of air movement that increases as the speed is increased. This appliance has several areas that reach high temperatures. Dust or other particles on these areas may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if the appliance was left idle for a long period. © Travis Industries 4071130 100-01196_000 10 Maintenance 10 Maintenance Maintaining Your Fireplace's Appearance Fingerprints or other marks left on the optional plated surface may become etched in place if they are not wiped clean prior to turning the fireplace on. Clean the plated surface with denatured alcohol and a soft cloth (with the fireplace cool). Other cleaners may leave a film that may become etched into the surface. Yearly Service Procedure • Failure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous situation. We recommend the following procedures be done by a qualified technician. 1. Check the pilot flame. It should touch approximately 3/8" of the top of the thermopile and touch the top of the thermocouple (see illustration below). If it does not, contact your dealer for service. 2. Shut off gas to the fireplace by turning the gas control knob to "OFF" (see step A under "Starting the Pilot" on page 7). Let the fireplace cool for 15 minutes. Remove the glass (see page 10). 3. Remove the log set (NOTE: the logs are very fragile - see page 15). If severely deteriorated, replace. Check the logs for sooting. A small amount of soot along the bottom of the logs is normal. If excessive sooting is found, the fireplace will require adjustment. Contact your dealer. 4. Inspect the burner and remove any debris. • Make sure the burner is not warped, cracked, or damaged. • Check the firebox and area around the pilot to make sure there is no warping or damage. • If any problem is found, discontinue use and contact your dealer for service. Check the walls and ceiling of the Before Disassembly -Check the pilot flame (it can firebox for deterioration. be viewed from the front - you will need to look under Check the burner holes. Make sure the burners are not warped or damaged. Thermopile Pilot Hood Thermocouple the center log). It should touch the thermocouple and thermopile. 5. Replace the log set. Clean and replace the glass (see Glass Cleaning on page 25). If the glass is damaged, replace. Make sure the gasket along the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it does not, re-align or replace the gasket to insure an air-tight seal. 6. Inspect the area behind the access door. Clean if necessary. Check the gas control valve and the gas lines. If damage is found, discontinue use and contact your dealer for service. Clean the air channels, ducts, and blower (if applicable). 7. Start the pilot and turn on the main burner. The flames should be orange/yellow and not touch the top of the firebox. If the pilot or main burners do not burn correctly, contact your dealer for service. Monitor the blower operation. 8. Remove any debris or vegetation near the ...