Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
OPERATION ELECTRIC FIREPLACE MANUAL CONTROL The manual controls for the fireplace are located in the lower right hand corner. A. Main On/Off Switch Supplies power to the 3 position manual control switch. B. 3 Position Manual Control Switch Remote (right position): The unit is operated with the remote control. Flame (center position): The flame effect is turned ON. Flame & Heat (left position): The flame effect and heater are turned ON simultaneously. When the manual control is in the Flame & Heat position the heater does not run on the remote operated thermostat. NOTE When the manual control switch is in the Flame and Flame & Heat positions, the fireplace unit will not operate with the remote control. Main On/Off Switch FIGURE 2 3 Position Manual Control Initialization Button RESETTING THE TEMPERATURE CUTOFF SWITCH Should the heater overheat, an automatic switch will turn the heater off and it will not come back on without being reset. The temperature cutoff switch can be reset by unplugging the unit, waiting 5 minutes and plugging the unit back in. CAUTION If you need to continuously reset the heater, unplug the unit and call Dimplex North America Limited at 1-800-668-6663 and press 4 for technical support. Please have your model and serial number ready when calling. REMOTE CONTROL The remote control has a range of approximately 50 ft. (15.25m), it does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with 243 independent frequencies to prevent interference with other units. BATTERY INSTALLATION 1. Depress tab on the battery cover on the back of the remote transmitter and remove battery cover. 2. Install 2 AAA batteries into the remote control. (included) 3. Ensure child lock is in the “unlocked” position. 4. Replace the battery cover. NOTE When the “BAT” symbol is present on the remote control it is recommended to replace the batteries promptly, to maintain full functionality of the remote/fireplace. The remote transmitter has a battery backup time of only several hours. INITIALIZING THE REMOTE CONTROL 1. Plug cord into 120 volt wall outlet. 2. Ensure the Main On/Off switch located in the switch box on the fireplace in the lower right hand corner is in the ON position. 3. Set the 3 position manual control to the Remote position (right position). 4. Press and hold the initialization button on the unit. 5. While holding the initialization button, press the flame/heat ON/OFF button or the Purifire™ ON/OFF button on the remote control transmitter. 6. Release the initialization button on the unit. 7. Press the Flame/Heat On/Off button to turn the Flame/Heat function ON or press the Purifire™ On/Off button to turn the Purifire™ function ON. Batteries FIGURE 3 FREQUENCY INTERFERENCE If the fireplace does not respond properly to the remote control, the remote operating frequency may have to be reset. The remote control can send another frequency code to the circuit board to eliminate interference. 1. Simultaneously press the “SLEEP TIMER DOWN” button and the “PURIFIRE LOW SPEED” button on the remote control. 2. “COD” will appear in place of the sleep timer digits. 3. Release the “SLEEP TIMER DOWN” button and the “PURIFIRE LOW SPEED” button. 4. Press the initialization button on the unit. 5. press the button on the remote. Your remote will now have a different frequency communicating with the fireplace. REMOTE CONTROL FUNCTIONS Sleep Timer Batteries On / Off Child Lock FIGURE 5 Temperature UpTemperature Down Dimmer Down Dimmer Up Flame Speed Down Flame Speed Up Sleep Timer Down Sleep Timer Up Purifire Low Speed Purifire High Speed Flame & Heat Purifire On / Off Purifire Room Temperature Set Temperature Dimmer Flame Speed Control FLAME/HEAT ON/OFF BUTTON Press the “Flame/Heat On/Off “button to turn the Flame/Heat function ON. When the “Set Temperature” is higher then the “Room Temperature” the heat will come on. To turn the heat off, lower the “Set Temperature” so that it’s setting is lower then the “Room Temperature”. The default temperature setting is 72°F (22°C). NOTE When using the remote control the heater runs on a thermostat. Press the “Temperature Up” or “Temperature Down” button to adjust the set temperature. Once the desired set temperature is reached the heater will turn OFF. The heater will cycle ON and OFF to maintain the desired set temperature. PURIFIRE ON/OFF BUTTON Press the “Purifire™ On/Off” button to turn the Purifire™ function ON. When the Purifire™ function is ON the Purifire™ symbol will flash. When off the symbol will be solid. The default setting for the Purifire™ is set at low speed. Press the “Purifire™ On/Off” button to turn the Purifire™ function OFF. NOTE To turn the Flame/Heat and Purifire™ “OFF” at the same time, press both control buttons simultaneously. SET TEMPERATURE 1. Press “Flame Heat On/Off” button to turn fireplace on. 2. Press “Temperature Up” to raise thermostat. 3. Press “Temperature Down” to lower thermostat. 4...