Stimmen - 6, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
4. Press and hold the Initialization Button on the unit (Figure 3C). 5. While holding the Initialization Button, press the Flame/ Heat On/Off button or the Purifire™ On/Off button on the remote control transmitter (Figure 5). 6. Release the Initialization Button on the unit. 7. Press the Flame/Heat On/Off button to turn the Flame/ Heat function on or press the Purifire™ On/Off button to turn the Purifire™ function on. Figure 4 Batteries Child Lock Operation Remote Control Functions (Figure 5) A. Room Temperature B. Set Temperature C. Light Dimmer Control D. Flame Speed Control E. Sleep Timer F. Purifire™ G. Purifire™ On/Off H. Flame & Heat On/Off I. Temperature Down J. Temperature Up K. Dimmer Down L. Dimmer Up M. Flame Speed Down N. Flame Speed Up O. Sleep Timer Down P. Sleep Timer Up Q. Purifire™ Speed Down R. Purifire™ Speed Up A B I J C K L D M N E O P F Q R G H B. Set Temperature Press H button to turn fireplace on. Press J to raise thermostat, or I to lower the thermostat. Press both J and I to change °F to °C. C. Light Dimmer Control While the fireplace is running, repeatedly press the L or K button to increase or decrease the brightness of the upper lights. D. Flame Speed Control While the fireplace is running, press the N button to increase the speed of the flame or press the M to decrease the speed of the flame. E. Sleep Timer The Sleep Timer automatically shuts off the fireplace after a preset time (from 30 minutes to 8 hours). During fireplace operation, to set the sleep timer press the P button. Set the timer from 30 minutes through 8 hours. The fireplace will automatically turn off when the sleep timer reaches zero (0) minutes. The sleep timer can be cancelled at any time by pressing the O button repeatedly until the sleep timer displays “0”. F. Purifire™ The Purifire™ includes a high efficiency filter to help improve the quality of air. Press the G button to turn the Purifire™ function on. When the Purifire™ function is on, the Purifire™ symbol will flash. When off, the symbol will be solid. The default setting for the Purifire™ is set at low speed. Press the Q or the R buttons to change between low and high speeds. Press the G button to turn the Purifire™ function off. H. Flame & Heat On/Off Button Press the H button to turn the Flame/Heat function on. When B is higher then A the heat will come on. To turn the heat off, lower the B so that it’s setting is lower then the A. The default temperature setting is 72°F (22°C). !NOTE: When using the remote control the heater runs on a thermostat. Press the J or I buttons to adjust the set temperature. Once the desired set temperature is reached the heater will turn off. The heater will cycle on and off to maintain the desired set temperature. Child Lock (Figure 6) Depress tab on the battery 1. cover on the back of the remote transmitter and remove the battery cover. Move Child Lock tab to 2. the right to lock the remote transmitter. Move Child Lock tab back to 3. the left to unlock the remote transmitter. Replace the battery cover.4. Operation !NOTE: To temporarily unlock the remote transmitter press (in order) I then J then K. When the remote transmitter’s backlight is illuminated the Child Lock is bypassed. When the backlight is off the Child Lock is re-activated. Frequency Interference If the fireplace does not respond properly to the remote control, the remote operating frequency may have to be reset. The remote control can send another frequency code to the circuit board to eliminate interference. Simultaneously press the 1. O. Sleep Timer Down button and the Q button on the remote control. “2. COD” will appear in place of the sleep timer digits. Release the 3. O button and the Q button. Press the Initialization button 4. on the unit (Figure 4C). Press the 5. H button on the remote. Your remote will now have a different frequency communicating with the fireplace. Operation Figure 6 Child Lock Switch Locked Unlocked Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Light Bulb Replacement Allow at least five (5) minutes for light bulbs and heater to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame. There are three (3) under the Log Set, which generate the flames and embers, and two (2) bulbs above the log that illuminate the log exterior. Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Care must be taken when removing the Log Set as the Log Set contains LED’s and wires. Lower Light Bulb Requirements Quantity of three (3) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 Watt rating. Example: GE 60BC or Philips 60CTC. Do not exceed 60 Watts per bulb. To access the...