Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Note: It may be easier to install the insulation, faceplate top and faceplate trim with the unit pulled slightly away from the fireplace face. If this is done, be very careful not to disturb the connector when shifting the unit to its fi nal position. Now that your insert is installed, check once more that all the clearances from the unit to any combustible materials are correct as listed earlier. Regency Wood Insert & Hearth Heater INSTALLATION Your fan should only be installed once the unit is in place in order to prevent any damage to the fan. To attach, follow the instructions provided with the fan. Make sure to install the rubber grommet to the fan housing before it is installed on the insert. 1) Remove the protective covering from the brass trim on the fan. 2) Align the fan support with the offset clip on the bottom of the ashlip. ThermoSwitchSensor FAN / BLOWER 3) Slide the supports into the clips. The tension Do not turn fan ON until your insert has holding the clips in place may be adjusted by reached operating temperature or at least increasing or decreasing the offset spacing 30 minutes after starting fi re. of the clips. 4) Ensure that the power cord is not in contact with any hot stove surfaces. 5) Push the Regency logo plate into the two holes in the front bottom left corner of the fan. ThermoSwitchSensorCAUTION: Label all wires prior to disconnection when servic- ing controls. Wiring errors can cause improper and dangerous operation. WARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. GroundFan Fan Black Black Black Fan Thermodisc (normally open) Blower/Fan Wiring Diagram Neutral Green Manual/ Live Ground Fan Auto 120V AC Switch Switch 60 Hz WhiteLow (Red) High (Black) Regency Wood Insert & Hearth Heater INSTALLATION FLOOR PROTECTION Please check to ensure that your fl oor protection and hearth will meet the standards for clearance to combustibles. Your hearth extension must be made from a non-combustible material. FIREBRICK ASSEMBLY Firebrick is included to extend the life of your insert and radiate heat more evenly. Check to see that all firebricks are in their correct positions and have not become misaligned during shipping. Large Insert (I3100L) Small Insert (I1100S) Hearth Heater (H2100M) DOOR HANDLE Attach spring handle by rotating counter clockwise onto rod. Ensure that the rod fits into the entire length of the spring handle. BRICK FLUE BAFFLE & SECONDARY AIR TUBE INSTALLATION The flue baffle system located in the upper area of the firebox is removable to make cleaning your chimney system easier. The brick baffl es must be installed prior to your first fire. Smoke spillage and draft problems may occur if the baffles are improperly positioned. Check the position of the brick baffles on a regular basis as they can be dislodged if too much fuel is forced into the firebox. The Large Insert I3100L is shipped with one of the secondary air tubes loose inside the firebox. It needs to be installed after the brick baffle are installed. Follow the directions below. Large Insert I3100L The unit arrives with the third air tube (from the front) and the 2 baffle bricks on the floor of the firebox. The baffle bricks are positioned first and then the air tubes are installed. 1) Slide the left baffle brick over the two rear air tubes and then push it all the way to the left side of the firebox. 2) Tilt the first Baffle Brick down and then slide the 2nd Baffle Brick up and back. Reposition both baffle bricks flat on the air tubes. 3) Important: push both baffl e bricks so they are tight against the side walls. Front View 4) Install the third air tube into the holes on the side channels. The notch goes on the right hand side with the air holes facing forward toward the door opening. If the tube will not slide in easily, simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter fit will ensure the tube will not move when the unit is burning. Note: When cleaning the chimney reverse the above procedures, removing the air tube and baffl e bricks and then replace them when cleaning is completed. Regency Wood Insert & Hearth Heater INSTALLATION Small Insert I1100S Hearth Heater (H2100M) 1) If the two air tubes are installed continue on Steel Baffl e to Step 2), if not, follow the instructions below. Install the air tube into the holes in the side channels. The notch goes on the right hand side with the air holes facing toward the door. Slide the tube into the left hand side, as far as possible and then bring it back into the hole on the right hand side until it locks into position. If the tube will not slide in easily simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter fit will ensure the tube will not move when t...