Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Wipe off all excess oil with a cloth before installing the blade. • Use caution when handling the blade so that you are not cut by the sharp edge of the blade teeth. Turn the blade tightening lever clockwise until it hits against the protrusion on the frame. 006191 1 2 4 3 1. Tighten 2. Loosen 3. Protrusion 4. Lever Start and stop the tool two or three times to make sure that the blade runs properly on the wheels. CAUTION: • While making sure that the blade runs on the wheels properly, keep your body away from the blade area. To remove the blade, follow the installation procedure in reverse. CAUTION: • When turning the blade tightening lever clockwise to release the tension on the blade, point the tool downward because the blade may come off unexpectedly. Adjusting the protrusion of stopper plate 006194 3 A B 1 1. Screw 2. Stopper plate 3. Blade 2 Protrusion of the stopper plate to the blade can be adjusted. 5 In the ordinary operation, protrude the stopper plate to start the tool and cut in to the cutting wax as shown in the the A side fully. figure after removing a cap of the cutting wax. In the ordinary operation, protrude the stopper plate to start the tool and cut in to the cutting wax as shown in the the A side fully. figure after removing a cap of the cutting wax. After sliding the stopper plate, secure it by tightening two screws firmly. OPERATION It is important to keep at least two teeth in the cut. Select the proper cutting position for your workpiece by referring to the figure. 004747 Hold the tool by both hands as shown in the figure with the stopper plate contacting the workpiece and the blade clear of the workpiece. 006195 Turn the tool on and wait until the blade attains full speed. Gently lower the blade into the cut. The weight of the tool or slightly pressing the tool will supply adequate pressure for the cutting. Do not force the tool. As you reach the end of a cut, release pressure and, without actually raising the tool, lift it slightly so that it will not fall against the workpiece. CAUTION: • Applying excessive pressure to the tool or twisting of the blade may cause bevel cutting or damage to the blade. • When not using the tool for a long period of time, remove the blade from the tool. When cutting metals, use Makita cutting wax as a cutting lubricant. To apply the cutting wax to the blade teeth, 006196 1. Cutting wax 1 CAUTION: • Never use cutting oil or apply excessive amount of wax to the blade. It may cause the blade to slip or come off unexpectedly. • When cutting cast iron, do not use any cutting wax. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning After use, remove wax, chips and dust from the tool, wheel tires and blade. CAUTION: • Never use solvents such as turpentine, gasoline, lacquer, etc. to clean plastic parts. • Wax and chips on the tires may cause the blade to slip and come off unexpectedly. Use a dry cloth to remove wax and chips from the tires. Replacing tires on wheels 004750 1 2 3 1. Wheel 2. Tire 3. Lip When the blade slips or does not track properly because of badly worn tires, or the lip of the tire on motor side gets damaged, the tires should be replaced. 6 Replacing fluorescent tube Replacing fluorescent tube 1 2 3 1. Fluorescent tube 2. lump box 3. Tapping screw CAUTION: • Always be sure that the tool is switched off and unplugged before replacing the fluorescent tube. • Do not apply force, impact or scratch to a fluorescent tube, which can cause a glass of the fluorescent tube to be broken resulting in a injury to you or your bystanders. • Leave the fluorescent tube for a while immediately after a use of it and then replace it. If not. You may burn yourself. Remove screws, which secure Lamp Box for the light. Pull out the Lamp Box keeping pushing lightly the upper position of it as illustrated on the left. Pull out the fluorescent tube and then replace it with Makita original new one. Replacing carbon brushes 001145 1 1. Limit mark Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 006197 1 2 1. Screwdriver 2. Brush holder cap To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more de...