Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
1423, 1424, 1428 Congratulations on your purchase of a Graco® swing! Graco is the recognized leader in the design and manufacture of quality baby swings. We believe your new Graco® swing is a wise choice, promising many hours of enjoyment for your baby. Before using your swing, please take a few minutes to read this Owner’s Manual. The short time you spend reading these instructions will help you use your swing properly. Please save your Owner’s Manual for future use. AWAI Failure to follow these warnings could result in seri< Always keep your child in view. DO NOT place items with a string around your child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings over the swing or attach strings to toys. STRANGULAT DO NOT place location where such as window drapes, phone Customer Satisfaction Our goal is to make every product the best it can be! We are also committed to supporting our products after purchase. If you would like to speak with Graco about your product, please contact our Customer Service Department at 1-800-345-4109 or visit our Internet website, Our knowledgeable staff will be ready to answer any questions you may have concerning parts, use or maintenance. When you call, please have the model and serial numbers ready so your call may be processed quickly and efficiently. THIS PRODUCT REQUIRES ADULT ASSEMBLY. FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY. If you experience any difficulties, please contact the Customer Service Department. DO NOT USE SWING without the seat cover. DISCONTINUE USING YOUR SWING should it become damaged or broken. © 2000 Graco 133-9-00 IS2491 2 3NING s and the assembly instructions ous injury or death. Avoid serious injury from falling or sliding out. Always use seat belt. ION HAZARD: swing in any there are cords, v blind cords, cords, etc. DO NOT use if child weighs over 25 pounds (11.3 kg) or becomes too active to safely use the swing. CARE AND MAINTENANCE FROM TIME TO TIME CHECK YOUR SWING for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco® replacement parts. REMOVABLE CLOTH SEAT COVER may be machine washed in cold water on delicate cycle and drip-dried. NO BLEACH. TO CLEAN SWING FRAME, use only household soap and warm water. NO BLEACH OR DETERGENT. EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts. PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your swing. If any parts are missing, call Customer Service at 1-800-345-4109 or visit our Internet website, Tool required: Screwdriver Seat cover Plastic seat with crotch strap ~U Tray Adjustment wire sv JUI Back brace Screw (4) □ Pin screw (2) Motor housing Pivot housing Large front Small rear Seat belt foot (2) foot (2) Rear base tube Toy mount cover (2) Leg (4) 3 4 Double / button ^ Single button Channels PUSH Button in hole Notch Attaching the Legs Step I. The four legs have a double button at one end and a single button beneath it. Hub With the hub sides facing up, place the motor housing and pivot housing on the floor. Position legs so their single buttons also face up. Insert legs into the motor housing and pivot housing as shown. The double buttons must fit into the channels inside the housings. Step 2. Push each leg in until the double button snaps into the hole at the end of the channel. Then swing the legs outward until the single button snaps into its notch, as shown. CHECK that the legs are properly attached by twisting them in the housings. They should resist twisting. If a leg twists and buttons come out of their holes, insert leg into the housing again. Be sure to align BOTH double buttons with BOTH sets of channels inside the housings. Attaching the Feet Step I. Identify the front and rear base tubes from pictures below. The feet to use with each tube can be identified by the text “FRONT BOTTOM” or “REAR BOTTOM” printed on them. Front foot Front base tube Rear base tube Step 2. Begin by inserting a screw all the way into the small hole on one foot. Position the foot as shown at right, so the text and viewing hole are not on the short side of tube near the wire end. Then use viewing hole to line up the end of the screw with the hole in the tube. Tighten the screw securely. Repeat above steps for the other feet. CHECK that feet are secure by wiggling the feet. Step 3. Push a plastic tip onto all four of the feet. Tap leg tips on the floor to be sure they are completely on. The hole in the plastic tip permits future tightening of the screw if needed. Attaching the Base Tubes Step I. Push the legs firmly onto the rear base tube exactly as shown. Bracket hole points toward rear of swing,. Step 2. Push the other two legs onto the front base tube. CHECK that all tubes are securely attached. CHECK that the parts of the frame are assembled in the positions shown. Motor housin...