4. Move the ShuttlePoint knob to highlight FISH FINDER and press [ENT] or move the ShuttlePoint knob to the right. CPF180i and CPF300i Page 109 5. Move the ShuttlePoint knob up/down to select OFF and press [ENT] or move the ShuttlePoint knob to the right. 6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart page is shown. 17.1 UNDERSTANDING THE FISH FINDER PAGE The display on CPF180i and CPF300i shows a time history of the echoes received by the transducer. The CPF180i and CP

2. Press [ENT] and move the ShuttlePoint knob to highlight TRIP LOG, press [ENT] or move the ShuttlePoint knob to the right. 3. A popup window will be shown with Nm (Nautical Mile), Sm (Statute Mile), Km (Kilometer) and RESET. Move the ShuttlePoint knob to select the desired units of measure and press [ENT] or move the ShuttlePoint knob to the right. Page 72 CPF180i and CPF300i 4. Press [CLR] or move the ShuttlePoint knob to the right until the selected page (Chart, Navigation, Highway or NMEA D

STANDARD HORIZON technical support personnel stands behind every product sold, and we invite you to contact us should you require technical advice or assistance. We appreciate your purchase of the HX750S, and encourage you to read this manual thoroughly, so as to learn and fully understand the capabilities of the HX750S. NOTE Water resistance of the transceiver is assured only when the battery pack is attached to the transceiver and MIC/SP cap is installed in the MIC/SP jack. WARNING This radio

Page 22 HX500S 8. OPERATING PRACTICES 8.1 EMERGENCY (CHANNEL 16 USE) Channel 16 is known as the Hail and Distress Channel. An emergency may be defined as a threat to life or property. In such instances, be sure the transceiver is on and set to CHANNEL 16. Then use the following procedure: 1. Press the microphone push-to-talk switch and say “Mayday, Mayday, Mayday. This is , , ” (your vessel’s name). 2. Then repeat once: “Mayday, ” (your vessel’s name). 3. Now report your position in latitude/lon

waters by using Channel 9 as the initial contact (hailing) channel for non-emergency communications. Here, also, calling time should not exceed 30 seconds but may be repeated 3 times at 2-minute intervals. Page 22 HX370S Prior to making contact with another vessel, refer to the channel charts in this manual, and select an appropriate channel for communications after initial contact. For example, Channels 68 and 69 of the U.S. VHF Charts are some of the channels available to non-commercial (recre

The transceiver changes to the weather channel mode. 2. Press the or key to change to other weather channels. 3. To exit from the weather channels, press the WX key. The transceiver recalls the previous non-weather channel. page 10 Owner’s Manual HX350S 4.7 SCAN 1. Select the desired channel to be scanned using the or key. 2. Press the MEM key to store the channel into the transceiver's memory. “MEM” is displayed on the LCD. 3. Repeat steps 1 and 2 for all the channels to be scanned. 4. To delet

11.6 CALL WAITING DIRECTORY The GX5500S logs received distress calls and individual calls. The DSC Call Waiting feature is similar to an answer machine where calls are recorded for review. When a call is logged while the radio is set on the DSC Standby function, a “ ” icon will appear on the LCD. The GX5500S can memorize up to the latest 30 Distress, and up to the latest 80 Individual Calls. 11.6.1 Enabling the Call Waiting Feature Follow the steps below to enable or disable the Call Waiting fea

FF520 Page 23 7. Move the ShuttlePoint knob to highlight YES and press [ENTER] to confirm. 8. Press [CLEAR] to exit. WARNING Turn Off and after few seconds turn On the Fish Finder in case of failed firmware upload. 3.4 SYSTEM INFORMATION PAGE FOR CP180/CP180i/CPV350 For troubleshooting you maybe asked by a Standard Horizon Product Support Technician for the software version of Fish Finder. The following procedure is how to access this information. 1. From the Chart Page, press [MENU] for two tim

2. Next move the ShuttlePoint knob until the cursor is over the Mark that you want to be the next leg in the Route. 3. Press [ROUTE]. You will notice a bearing line joins the first and second Mark which means these Marks are selected into the Route. 4. Repeat steps 3 and 4 until all Marks are entered into the Route. NOTE At this point the Route is saved as ROUTE01. If you would like to save the Route under a specificname follow the steps on the previous 9.1 paragraph. Page 52 CP500 9.4 INSERTING

A popup menu will appear with time selections, move the ShuttlePoint knob to the desired selection and press “ENTER”. 3.11.1 Selecting a track line color The chart plotter has 8 different line colors that you can choose for the track plotter. To select from press “MENU”, select TRACK, press “ENTER”, use the ShuttlePoint knob to select LINE COLOR, press “ENTER” and choose the color using the ShuttlePoint knob. 3.11.2 Turning on or off the Track plotter Press “MENU”, select TRACK and press “ENTER”