Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
A copy of the original sales receipt is required as the proof of purchase for warranty repairs. November 2006 Part Number 190-00579-00 Rev. C Printed in Taiwan Mounting Holes Marine Network Mounting Holes Marine Network INTRODUCTION INTRODUCTION Thank you for choosing the Garmin GSD 22 Sounder Module. The GSD 22 is a CANetTM and Garmin Marine Network compatible, remote sounder module designed to include powerful features found in other Garmin sounders, including Color Depth Control Gain (DCG®), DynacolorTM, and auto gain features technology. When used with compatible Garmin chartplotters, it provides full-featured depth sounder functions. It can interface to multiple head units, providing complete sounder control from multiple stations, including transmit frequency, range, and gain adjustments. To get successful results from your GSD 22, take time to read through this installation guide. If any items are missing, contact your Garmin dealer immediately. Included Equipment: • GSD 22 Sounder Module • 6 ft (0.30 m) Power/Data Cable • 6 ft (0.30 m) Marine Network Cable • 40 ft (12.19 m) CANet Extension Cable • 1 Field Install Marine Ethernet Connector • 1 Marine Grommet • 2 CANet Terminators • 7 3-Wire Connectors • The GSD 22 Sounder Module Installation Instructions Optional Transducers The transducer acts as the eyes and ears of your new sonar. The transducer transmits sound waves toward the bottom in a cone shape. The larger the cone angle, the larger the coverage area at a given depth. Proper transducer selection and installation are critical to the operation of your unit. Since mounting locations vary, see your local dealer or contact Garmin Product Support for further information. A full list of transducers can be found at Power/Data Connector Connector Transducer Connector GSD 22 Sonar Module INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS The GSD 22 must be properly installed according to the following CANet or Marine Network installation instructions to get the best possible performance. Refer to your chartplotter to determine the correct installation method. To complete the installation, you need appropriate fasteners. If you experience difficulty with the installation, contact Garmin Product Support. The module should be mounted in an out-of-the-way location that is dry and well ventilated. Avoid mounting the module where it can be submerged in liquids or exposed to extreme temperatures. Be sure to mount the module so that the LED is visible. To install the GSD 22 sounder module: 1. After the location is chosen, place the unit. Be sure to allow enough clearance for attaching the cables. Using the module as a template, mark the location of the four mounting holes. 2. Attach the GSD 22 to the mounting location using appropriate fasteners. 3. Mount the transducer according to the instructions provided with the transducer. 4. Route the cables according to the CANet or Marine Network instructions on the next 3 pages. Use appropriate tie-wraps, fasteners, and sealant to secure the cable along the route and through any bulkhead or deck. 5. After installing the GSD 22 module, connect the power/data and transducer cables to the appropriate receptacle. 6. Refer to the following CANet or Marine Network wiring diagrams for connecting the GSD 22 to compatible Garmin units. NOTE: You can extend the CANet wiring of the GSD 22 power/data cable up to 80 ft (24.38 m) total length using the CANet Connections Kit. NOTE: You can extend the power wiring of the GSD 22 power/data cable up to 100 ft (30 m) total length using 18 AWG wire. Transducer cable extensions are available through your Garmin dealer. GSD 22 Wiring Connection To install the power, transducer, and network cables: 1. Align the notch and locking ring tab on the black Power cable with the POWER port on the front of the GSD 22. Carefully press the cable in until it is firmly seated. Do not force the cable, as this may damage the pins! 2. After the cable is seated, turn the locking ring clockwise until it stops. 3. Repeat steps 1 and 2, attaching the transducer cable to the TRANSDUCER port on the unit. 4. If networking the MFD with the Garmin Marine Network, insert the RJ-45 connector into the NETWORK port on the back of the unit and screw the locking ring in clockwise until it is firmly seated. The CANet installation does not require the NETWORK port. With power applied to the circuit, test the installation by pressing the POWER key on the front of the MFD. The GSD 22 turns on automatically when the MFD is turned on. WARNING: During peak transmit conditions, the heat sink might become hot. WARNING: Do not connect or disconnect the transducer while the MFD and GSD 22 are connected and turned on . Doing so might damage the GSD 22. NOTE: When using the chartplotter and GSD 22 on battery power only (engines off) for extended periods of time, be sure there is enough available amperage to run the units for the time period. Running other onboard d...