Gal. / Liters) 5 / 18.9 9 / 34 13.5 / 51 Fuel Consumption (Gal. Per Hr / Liters Per Hr) .52 / 1.97 .85 / 3.00 1.2 / 4.54 Pump Pressure (psi) 4.7 5.1 5.6 Electric Requirements 120V / 60 HZ 120V / 60 HZ 120V / 60 HZ Amperage (Normal Run) 2.8 3.6 3.6 Motor RPM 3440 3400 3400 Hot Air Output (CFM) 360 490 575 Motor HP 1/8 1/5 1/5 Shipping Weight (Approximate Pounds / Kilograms) 36 / 16.3 56 / 25.4 71 / 32.2 Space heater Weight without Fuel (Approximate Pounds / Kilograms) 32 / 14.5 48 / 21.8 61 / 27.

Wash filter assembly in clean fuel and inspect for damage. Note: It is not necessary to remove filter from filter assembly on Model T70. On Model T115 and T165 assembly is one piece. 5. Install filter assembly and bushing (Model T70) into fuel tank. IMPORTANT: Be sure filter (Model T115 and T165) and bushing (Model T70) are firmly seated in tank. 6. Connect fuel line and install side cover. Model T70 B C A Model T115 and T165 C A B 107351-01 19 Periodic Service STORAGE LOCATION AND MAINTENANCE N

7. Keep space heater area clear and free from combustible materials, gasoline, paint thinner and other flammable vapors and liquids. 8. Never use space heater in living or sleeping areas. 9. Never leave a space heater plugged in without adult supervision if children or animals are likely to be present. Do not leave heater unattended. 10. Never move, handle or service a hot or operating heater. Severe burns may result. You must wait 15 minutes after turning heater off. WARNINGWARNINGSINTHEMANUALS

It has only information you need for normal operation and maintenance. If a technical manual is desired, see your John Deere dealer for the correct manual. USING SERVICE RECORDS 1. Keep a record of the number of hours or operation. 2. Check your record regularly to learn when service is required. 3. Do all the services in the interval section. Then write the number of hours (from your service record) and the date in the spaces provided. Sample Service Record Chart Date Hours 1 Jun '85 3 6 Jun '8

Clean photocell lens. Check electrical connections. Replace photocell. Replace ignition control assembly. Operator’s Manual Service MAINTENANCE PREVENTATIVE MAINTENANCE SCHEDULE: WARNING: HIGH VOLTAGE. NEVER SERVICE Space heater WHILE IT IS PLUGGED IN, OPERATING, OR HOT. SEVERE BURNS AND ELECTRICAL SHOCK CAN OCCUR. Item How Often How to Fuel tank Flush every 150-200 hours of operation or as needed. See "Storage: Storing, Transporting, or Shipping". Air output and lint filters Replace every 500 h

HANDLE WITH CARE. 8. Carefully remove replacement ignitor from packing. Air Line Hose Fuel Line Hose Photocell Bracket Photocell Assembly Side Cover (Fig. 14) Ignitor Screw/ WasherAssembly Ignitor Element Photocell Bracket Ignitor Ignitor Wire Ignition Control Assembly Ignitor Nozzle Adapter Bracket 9. Carefully guide ignitor into opening in nozzle adapter bracket. Do not strike ignitor element. Attach ignitor to nozzle adapter bracket with screw using a 1/4" nut driver (Fig. 16). Torque .90 to

Install heater assembly (A) to wheel support frame (B). Align holes in heater assembly and wheel support frame. Note:Wheels are to be at hot air outlet end of heater on T70 ONLY (see next picture below). 2. Install fuel gauge cap (C). A C B 3. Install rear handle (A) using screws (B) and lock nuts (C). DO NOT TIGHTEN. Model T70 Shown A B C 4. Install front handle (A) (excluding T70) using screw (B) and lock nuts (C) DO NOT TIGHTEN. 5. Tighten all screws and nuts. B A C 107351-01 23 Specification

Set gap between ignitor electrode and nozzle to .13"/.15" (3.3/3.8 mm) c. Replace ignitor electrode. See "Maintenance: Ignitor". d. Replace spark transformer. See "Maintenance: Spark Transformer". Operator’s Manual Troubleshooting WARNING: HIGH VOLTAGE. NEVER SERVICE SPACE HEATER WHILE IT IS PLUGGED IN, OPERATING, OR HOT. SEVERE BURNS AND ELECTRICAL SHOCK CAN OCCUR. Symptom Heater shuts down while running. Heater producing odor. Problem Propane / L.P. supply may be inadequate. High surrounding a

5) .075 inch (Fig. 6) Operator’s Manual Service 6. Remove pressure gauge. Replace pressure gauge plug (Fig. 9) in fuel pump port marked “GAUGE.” PUMP: (Procedure if Pump is Binding) 1. Remove upper shell (Maintenance: Upper Shell Removal). 2. Loosen hex screw on flange clamp at rear of motor with 5/16" nut-driver (Fig. 9). 3. Turn fan with hand (Fig. 10). 4. If fan turns freely, tighten screw on flange clamp. 5. If fan does not turn freely, replace pump. NOZZLE: 1. Remove upper shell. (see Mante

If more than one heater is used, include equivalent ventilating area. • Provide adequate clearance from people, animals, and combustible materials - 8 feet (2.4 m) from heater outlet; 6 feet (1.8 m) from top; 4 feet (1.2 m) from sides. • Be sure there is no obstruction in intake or output openings. • Be sure heater is on a level, stable surface. • Depending on thermostat setting, heater can start immediately when power cord is connected. • Be sure electrical circuit is adequate and properly grou