Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
In ‘MANUAL MODE’ you can: • turn on the main burner • regulate the flame from low to high and back • turn off the burner leaving just the pilot burning In ‘TEMP MODE’ you can: • set the room temperature so the thermostat in the remote automatically maintains that temperature In ‘TIMER MODE’ the fire: • turns on and off according to the set time periods • automatically regulates the room temperature during the set periods NOTE: When operating the fire in Temp or Timer mode, the pilot remains lit and the fire then automatically switches on at programmed times to bring the room to the set temperature whether or not you are in the room. NEVER LEAVE ANY COMBUSTIBLE MATERIALS WITHIN 1 METRE OF THE FRONT OF THE APPLIANCE. 2.1 SWITCHING BETWEEN MODES • Press the SET button to change to Manual Operation • Press again to change to Temperature Mode • Keep pressing to run through all operating modes. These are: • MAN • DAY TEMP • NIGHT TEMP • TIMER and back to MAN NOTE: MAN mode can also be reached by pressing either the UP or DOWN arrow 2.2 MAN MODE • Press both the UP arrow and immediately press the OFF button to light the appliance. You hear a click as the fire begins the ignition process , (up to 30 seconds) • Press the OFF button to turn the appliance off INCREASING TEMPERATURE • Press the UP arrow once to increase flame height one stage • Press and hold the UP arrow to increase to maximum DECREASING TEMPERATURE • Press the DOWN arrow once to decrease flame height one stage • Press and hold the DOWN arrow to decrease to minimum At the lowest point the fire goes to ‘standby mode’ (only pilot lit) NOTE: While pressing a button a symbol indicating transmission appears on the display. The receiver confirms transmission with an acoustic signal. 4 Turning the Linea Off • Press the Off button to extinguish the pilot 2.3 TEMP MODE The display shows the current room temperature. To increase or decrease the fire’s output: • Press the SET button to select either the DAY TEMP or the NIGHT TEMP mode by briefly pressing the SET button • Hold the SET button until the TEMP display flashes and then let go • Set the desired temperature with the UP and DOWN arrows. (Minimum temperature 5C, maximum 30C or fahrenheit) • Press the OFF button to stop the display flashing or wait to return to TEMP mode. NOTE: If you set a temperature that is beneath the current room temperature, the fire automatically switches to OFF. NOTE: If you would like the Night temperature control to turn off then decrease the temperature until [---] is displayed. 2.4 TIMER MODE There are two programmable settings you can make over a 24 hour period, P1 and P2 P1 + = Start Timed Setting 1 P1 + = End of Timed Setting 1 P2 + = Start Timed Setting 2 P2 + = End of Timed Setting 2 2.4.1 P1 - Program 1 for a Timed Setting • Press the SET button until the TIMER mode is displayed • Hold the SET button. The displays flashes the current time for P1. While the time displayed is flashing you can alter the hours and minutes set. To set the time your fire first lights, change the Start Timed Setting for P1. • Press the UP arrow to alter the hour • Press the DOWN arrow to alter the minutes in 10 minute increments • Press SET again to move to the End of Timed Setting, P1. The display shows the current setting for P1 This is the time your Linea first shuts down: • Press the UP arrow to alter the hour • Press the DOWN arrow to alter the minutes 2.4.2 P2 - Program 2 for a Timed Setting Use the same steps outlined in 2.4.1 to change the setting for P2. If you have already set P1 and want to alter the setting for P2 only: • Press the SET button until TIMER mode is displayed • Hold the SET button until the display flashes the current time for P1 • Press the SET button again to scroll past the settings for P1 and P1 With the time still flashing: • Press the UP arrow to alter the hour • Press the DOWN arrow to alter the minutes Once all four times are set press the OFF button or simply wait to complete programming. 2.5 LOW BATTERY “BATT” is displayed on the remote when its batteries need replacement. 2.6 SETTING THE TIME • Simultaneously press the up and down arrow buttons • Press the up arrow to set the hour and the down arrow to set the minutes • Press OFF to return to the manual mode or simply wait 2.7 SETTING THE °C/24 HOUR OR °F/12 HOUR CLOCK • Press OFF and the down arrow until the display changes from °C/24 hour clock to °F/12 hour clock and vice versa. If the remote is removed, lost or damaged, signals transmitted to the receiver cease. Your fire will go to standby (pilot) mode after 6 hours. 2B TOUCH PAD CONTROL 2AR1885 • Press the ON-OFF button to light the appliance, (up to 30 seconds) • Press the UP button to increase the flame height • Press the DOWN button to decrease the flame height. At the lowest point it goes to ‘standby mode’, (only pilot lit) • Press the ON-OFF button to turn the appliance off USER INSTRUCTIONS 5 EMERGENCY SHUT OFF If the batteries fail during use of t...